S T E P 1 2
Apply a bead of silicon or any adhesive sealant around the hole of the supplied aluminum plate.
|
|
| ||
I N C L U D E D H A R D W A R E |
|
|
| |
(4) | (1) | |||
(2) | (2) | |||
(4) | (2) Foam Flooring Spacers | |||
(2) | (1) | Carpeted Flooring | ||
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type:
Nominal Impedance: 4 ohms mono
Continuous Power Handling: 300 Watts
BRACKET FROM STEALTHBOX
VEHICLE'S FLOOR
ALUMINUM PLATE(front bolt assmebly only)
FLAT WASHER
HEX NUT
HEX HEAD BOLT FLAT WASHER
FENDER WASHER LOCK WASHER
S T E P 1 3
From under the vehicle, place the supplied aluminum plate(front bolt assembly only), fender washers, flat washers, lock washers and then hex nuts onto each protruding hex cap screws and secure.
Note: For added protection, it is recommended that you apply a bead of silicone between the vehicle and the fender washer. After the bolt assembly is tightly secured, it is also recommended that vehicle under- coating material is applied to the exposed assembly.
S T E P 1 4
Place both supplied foam supports around the spare tire as shown to the left.
Place the spare tire with the yellow side up onto the Stealthbox® and secure with the factory hold down bolt that was removed in STEP 1.
Place the supplied replacement flooring into vehicle. Note: If the child LATCH system will be used, slight modification of the supplied flooring is required.
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an amplifier recommendation and basic
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.
+12VDC Ground Remote | Preamp Output Section | Bass Control | Amp LP Filter | Amplifier Input Section | |||
| Output Mode | Infrasonic Filter | Mode/Slope | Input Voltage | Input Sens. Signal Sensing | ||
|
| Off/30Hz | Off/12dB/24dB | Low/High | Off/On | ||
|
|
|
| +7 |
|
|
|
|
|
| +3 | +10 |
|
|
|
JL AUDIO 250/1 |
|
| +1 | +13 |
|
|
|
|
|
|
|
|
|
| |
monoblock subwoofer amplifier |
|
|
|
|
|
|
|
| Left Ch. | Right Ch. | LF Boost (dB) | Filter Freq. (Hz) | Left Ch. | Right Ch. | |
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for even more detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
Fits JL Audio Models:
Rear Speaker Size / Location:
Fits JL Audio Models:
(954) | www.jlaudio.com |
|
|
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
Page 3 • JL Audio, Inc 2006
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A