Maxxsonics GPV1600.4 manual Way active, or bi-amplified system with mono bass, Right to Channels

GPV1000.4 / GPV1600.4 4 CHANNEL AMPLIFIER APPLICATIONS

2 way active, or bi-amplified system with mono bass

This application shows how easily a 2 way active system can be implemented using a 4 channel amplifier. Channels 1 and 2 will be used for highs, and channels 3 and 4 for mono bass.

Interconnect cable checklist:

-We need to feed the same signal to both sets of channels, so must use 2 Y-adapters, one to feed the LEFT signal to channels 1 and 3, and the right signal to channels 2 and 4, as shown.

Mono bass woofer wiring:

-Connect the mono speaker positive terminal to the LEFT +, and its negative terminal to RIGHT -.

Switch setting checklist:

-1/2CH X-OVER: HP

-3/4CH X-OVER: LPF

LEFT TO

CHANNELS

1 AND 3

Crossover frequency control checklist:

Channels 1/2:

-HI PASS: 100 Hz

-LOW PASS: N/A Channels 3/4:

-HI PASS (subsonic): 20 Hz

-LOW PASS: 100 Hz

Please note that these frequency points are suggestions only. Refer to the loudspeaker manufacturer specifications and the section “Setting up systems after installation for best performance”

Level control checklist:

Refer to the section “Setting up systems after installation for best performance”

Minimum final loudspeaker impedances:

-2-Ohms per channel in stereo mode.

-4-Ohms mono bridged.

RIGHT TO

CHANNELS

3 AND 4

CH3/4	L		R
				LINE
C				INP
1/2				T
CH1 CH2	+ - gnd - +	HI INPUT	+ - gnd - +	CH3 CH4
5V 0.2V	LEVEL	5V 0.2V		LEVEL
0dB 12dB 60Hz 1.2KHz CHANNEL 1 / 2	BASS EQ HPF	0dB 12dB 60Hz 1.2KHz		BASS EQ HPF	CHANNEL 3 / 4
30Hz 250Hz	LPF	30Hz 250Hz		LPF
FULL LPF HPF	X-OVER	FULL LPF HPF		X-OVER
		CHANNEL	2 3 4	MODE
				LINE OUT

30th ANNIVERSARY

GROUND POUNDER

OUTPUT	- LEFT +
CH 3/4 SPEAKER	RIGHT +
	-

FUSE
POWER INPUT	GND REM +12V
OUTPUT	- LEFT +
SPEAKER	+
CH 1/2	RIGHT
	-

	MONO
BRIDGED
	SUB BASS
	SPEAKER

TO BATTERY + 12 Volts VIA FUSE REMOTE TURN-ON

CHASSIS GROUND

	STEREO
BRIDGE	HIGHS
	SPEAKERS

2 way active, or bi-amplified system with mono bass, and faded highs/lows

Here we present a variation of the previous system. Since this is a 2 way system, we can use the front outputs from a head unit to drive the highs, and the rear output to drive the bass This method allows the listener to easily adjust the relative levels of bass to highs, with the front to rear fade on the head unit.

Channels 1 and 2 will be used for highs, and channels 3 and 4 for mono bass.

Interconnect cable checklist:

-Use good quality RCA leads to connect the inputs of the amplifier to the source as shown.

-Follow the instructions as per the previous system for switch and crossover settings.

FULL RANGE STEREO LINE INPUTS

CH3/4	L
				LINE
CH1/2				INPUT
1 CH2	- gnd - +	I INPUT	- gnd - +	CH3 CH4
5V 0.2V	LEVEL	5V 0.2V		LEVEL
0dB 12dB 60Hz 1.2KHz CHANNEL 1 / 2	BASS EQ HPF	0dB 12dB 60Hz 1.2KHz		BASS EQ HPF	CHANNEL 3 / 4
30Hz 250Hz	LPF	30Hz 250Hz		LPF
FULL LPF HPF	X-OVER	FULL LPF HPF		X-OVER
		CHANNEL	2 3 4	MODE
				LINE OUT

30th ANNIVERSARY

GROUND POUNDER

OUTPUTSPEAKER3/4CH	-+RIGHTLEFT +	BRIDGED			MONO
					SUB BASS
	-				SPEAKER
FUSE			TO BATTERY + 12 Volts VIA FUSE
POWERINPUT	REMGND+12V
			REMOTE TURN-ON
			CHASSIS GROUND
OUTPUT	- LEFT +			STEREO
SPEAKER		BRIDGE
	+				HIGHS
CH 1/2	RIGHT
				SPEAKERS
	-

6