Panasonic C9801W Preparation Before Initial Use, Using Subwoofer, Press Disp Display

Preparation

When the power is switched on for the first time, a demonstration message appears on the display. Press [DISP] to change to regular mode.

SRCCS

On		1 Set your car’s ignition switch to the ACC
		or ON position.
PowerTimeFirst	(DEMONSTRATION)
		The demonstration screen appears.
		Example: CQ-C9901W
		2 Press [DISP: DISPLAY].
		The demonstration screen is cancelled, and no more
		appears.		Note: If you would like to turn on the power and make
				the demonstration message appear, hold down [SRC]
				(PWR: POWER) for 4 sec. or more.
		Preparation Before Initial Use		Warning
		Pull the insulation film out		¡Keep batteries and insulation film out of reach
Preparation		from the backside of		of infants. If an infant ingests a battery, please
		remote control gently.		seek immediate medical attention.
				Caution
		Insulation film		¡ Remove and dispose of an old battery immediately.
				¡ Do not disassemble, heat or short a battery.
		Battery Replacement
Control				Do not throw a battery into a fire or water.
		q Remove the battery holder	Tough pointed object	¡ Follow local regulations when disposing of a
				battery.
		with the remote control unit	Back side
				¡Improper use of a battery may cause overheat-
		placed on a flat surface.
				ing, an explosion or ignition, resulting in injury
Remote		q Stick your thumbnail into	w
		same time.		¡Battery Information:
		the groove, and push the		or a fire.
		holder in the direction of
		the arrow, and at the		Note:
		w Pull it out in the direction	q	Battery Type: Panasonic lithium battery (CR2025)
		of the arrow using a
			2	(Included in the remote control)
		tough pointed object.
				Battery Life: Approximately 6 months under nor-
		w Put a battery in the case with
		(+)-side facing up.		mal use (at room temperature)
		e Put the case back.
			3
FunctionSecurity	Setting	The following functions are activated when the Security		¡ The alarm sounds and the message appears on the
		Function is ON. (a page 34)		screen to warn you to remove the face plate at power
		¡ The security indicator blinks when removing the face		off.
		plate.
		Security Indicator

You may need to set the following depending on the devices to be connected.

Using Subwoofer

¡Subwoofer level adjustment (a page 32)

¡Subwoofer low pass filter (a page 32)

Other Settings

Note: Adjust the clock when “ADJUST” appears on the display.

	1 Press [MENU] to display the menu dis-
adjustment ADJUSTMENT)CLOCK	play.
	For using the remote control, hold down [MENU]
	for 2 sec. or more.
	2 Press []] or [[] to display the DIS-
	PLAY menu.
Clock (CLOCKADJ:	3 Press [{] to select “CLOCK ADJ”.
	4 Press [BAND] (SET) to confirm the dis-
	play.

	English
to TV.
Connecting an AV device (TV, VTR)
If you connect TV to AUX1 terminal, set the AUX1 setting
1 Press [SRC: SOURCE] to select the
	Preparation
AUX1 mode. (a page 14)
2 Press [MENU] to display the menu dis-
play.
For using the remote control, hold down [MENU]
for 2 sec. or more.

3 Press [BAND] (SET) to adjust.

: TV

: Other devices (Default)

Note: When using an external TV unit manufactured by a third party, select the TV mode.

4 Press [MENU] to confirm the adjust- ment.

5 Adjust the setting value.

[[]: Adjusting minutes

[]]: Adjusting hours

[}]: Forward

[{]: Backward

6 Press [BAND] (SET) to confirm the adjustment.

Note: For cancellation of clock adjustment, press

[DISP].

7 Press [MENU].

For using the remote control, hold down [MENU] for 2 sec. or more.

10 CQ-C9901W/C9801W CQ-C9901W/C9801W 11