Integra ADM-2.1 instruction manual Connection diagram, Speakers, AC Inlet

Rear panel facilities and connections

SPEAKERS

Connect the jacks on the speakers to the SPEAKERS terminals using the speaker cables. These terminals are compatible with banana plug connections.

1Strip away 15 mm (5/8 in.) of wire insulation.

2Twist wire ends very tight.

3Unscrew.

4Insert wire.

5Screw.

1	15mm	2
	(5/8 in.)
3	4	5

•When you are using only one speaker or when you wish to listen to monaural (mono) sound, a single speaker should never be connected in parallel to both the right and left- channel terminals simultane- ously.

•To prevent damage to cir- cuitry, never short-circuit the positive (+) and negative (–) speaker wire.

AC INLET

NO!

+ –	– +	+ –	– +
R	L	R	L

NO!

•Do not connect any devices other than speakers to these terminals.

•Be sure not to mistake the positive and negative outputs or the left and right speakers. Doing so will result in an unnatural sound space.

•Only connect speakers with an impedance of 6 ohms or higher. If a speaker with an impedance of less than 6 ohms is connected, it may damage the ADM-2.1.

Plug the supplied power cord into this AC INLET and then into the power outlet on the wall.

•Do not use a power cord other than the one supplied with the ADM-2.1. The power cord supplied is designed for use with the ADM-2.1 and should not be used with any other device.

•Never disconnect the power cord from the ADM-2.1 while the other end is plugged into the wall outlet. Doing so may cause an electric shock. Always connect by plugging into the wall outlet last and disconnect by unplugging from the wall outlet first.

Connection diagram

Since the many users will purchase the ADM-2.1 together with the DTR-7.1, here is an explanation of how to connect the ADM-2.1 to the DTR-7.1.

12V TRIGGER OUT jack

					ANTENNA		AM	FM	COMPONENT	RS 232
			REMOTE					75	VIDEO
	DIGITAL		CONTROL
	OUTPUT				12 V				Y
	(OPTICAL)		PRE
					TRIGGER				INPUT 1
			R OUT	L	B	A	ZONE 2	MAIN
	1		FRONT					IR IN	PB
	DIGITAL				R		L	VIDEO	S VIDEO
	INPUT
PRE OUT	(OPTICAL)		SURR
	2							OUT	PR
		GND	SURR	(SB)			VIDEO
			BACK					1
SURR BACK	1							IN	Y
	DIGITAL		SUB
	INPUT		WOOFER	CENTER					INPUT 2
	(COAXAL)
jacks	2							OUT	PB
	R	L					VIDEO
								2
	FRONT
			OUT					IN	PR
			TAPE				VIDEO
								3

When connecting the ADM-2.1 to 2 channel control amplifier or preamplifier, connect the AUDIO IN jacks of the ADM-2.1 to the PRE OUT FRONT jacks of the control amplifier or preamplifier, and connect the front speakers to the SPEAKERS terminals of the ADM-2.1.

DTR-7.1

R	L	FRONT
		SPEAKERS
		CENTER	AC OUTLETS
			AC 120V 60Hz
		SPEAKER
SURR			SWITCHED
BACK			TOTAL 120W 1A MAX.
SPEAKER

R	L
	SURR
	SPEAKERS

	MAIN
R	L	CAUTION:
		SPEAKER IMPEDANCE

ZONE 2

SPEAKERS 6 OHMS MIN. PER EACH

SPEAKER TERMINAL

SURR	IN				IN	Y
	(SB)				DVD	OUTPUT
SURR	CD					PB
					IN
BACK
SUB	PH					PR
WOOFER
MULTI CHANNEL	CENTER			ZONE 2	MONITOR
				OUT	OUT
INPUT	R	L	R	L	VIDEO	S VIDEO

ZONE 2

AV RECEIVER

MODEL NO. DTR-7.1

AC INLET

ADM-2.1

AC INLET

GND SPEAKERS 2 CHANNEL AMPLIFIER

MODEL NO. ADM-2.1

AUDIO		INPUT	TRIGGER	12 V	L	L
		LEVEL		TRIGGER
OUT	IN
L		L
			12 V
			AUDIO OFF TRIGGER		R	R
				IN
R		R

MIN MAX

Set to 12V TRIGGER.	Surround	Surround
	back right	back left
	speaker	speaker

Power cord (supplied)

To an AC	5
wall outlet

#US_ADM-2.1_04-07.p65 5 8/25/00, 6:22 PM