Kenmore 790.42003 manual Before You Call, Fan noise during cooking operation

Page 18

Before You Call

Solutions to Common Problems

Before you call for service, review this list. it may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance.

OCCURRENCE

Oven Control Beeps and Displays any F code error (example Fll).

"d=o" is dispJayed.

Appliance not level.

Poor cooking results,

Entire oven does not operate.

Oven light does not work.

Fan noise during cooking operation.

POSSIBLE CAUSE/SOLUTION

Electronic control has detected a fault condition. Press any key to clear the display and stop the beeping. Reprogram the oven. if a fault reoccurs, record the fault number. Press any key and call Sears or another qualified servicer.

The door was left open and controls set for self-cleaning cycle. Just close the door to correct the problem.

Place oven rack in center of oven. Place a level on the oven rack. Contact installingagent if rack and cabinet cutout flooring are not level.

Kitchen cabinet misalignment may make oven appear to be not level. Be sure cabinets are square and level. Contact cabinet maker to correct problem.

When the oven is first plugged in, or when the power supply to the oven has been interrupted, the display will flash. The oven cannot be programmed until the clock is set.

Be sure electrical cord is securely connected into the electrical junction box.

Cord/plug is not installed and/or connected. Cord is not supplied with oven. Contact Sears or another qualified servicer.

Service wiring not complete. Contact Sears or another qualified servicer.

Power outage. Check house lights to be sure. Call your local electric company.

Short in cord/plug. Replace cord/plug.

Controls are not set properly. See instructions under Setting Oven Controls to set the controls.

House fuse has blown or circuit breaker has tripped immediately following installation. House fuse may not be fully engaged. Check fuse and screw or engage circuit breaker securely.

House fuse has blown or circuit breaker has tripped after the oven has been installed and previously operating. Contact Sears or another qualified servicer.

Burned-out or loose bulb. Follow the instructions under Changing Oven Light to replace or tighten the bulb.

A cooling fan may automatically turn on and off to cool internal parts. This is normal, and the fan may continue to run even after oven is turned off.

In self-clean mode, the blower in both ovens will start when using one of the

ovens.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Lectricoven Iii Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.ATable of Contents Read all instructions before using this appliance Save these instructions for future referenceProduct Record Serial Plate LocationSerialtion For prices and additional information call 1-800-827=6655 Maintenance AgreementsJn the U.S.A AgreementWall Oven FeaturesElectric YourOven Vent and Racks Arranging Oven RacksOven Ladder Racks Set Control Button FeaturesSetting the Clock ClockSetting the Clock contd Setting Oven ControlsOven Baking Setting Convection Roast Setting Oven ControlsSetting Convection Bake Setting Convection ConvertUsing the Temperature Probe Feature Setting the Bread Proof FeaturePreparing Bread Dough In The Oven To set Warm & Hold Setting the Warm & Hold TM FeatureSetting Broil To set the oven to broilWhat to Expect during Cleaning Self-CleaningSelf=Cleaning Oven Adhere to the following cleaning precautionsSelf=Clean Cycle Time Length Self-CleaningAdjusting Oven Temperature Stopping or Interrupting a Self=Cleaning CycleGeneral Care & Cleaning Cleaning Various Parts of Your OvenSpecial Door Care Instructions Care and Cleaning of Stainless SteelRemoving and Replacing the Oven Door Changing the Oven LightBefore You Call Fan noise during cooking operationSolutions to Common Problems Oven smokes excessively duringVent Canada MY-HOIVIESears.com No matter who made it, no matter who sold it
Top Page Image Contents