Pioneer GM-3200T owner manual Before Using This Product, English, Information to User

Page 1

BRIDGEABLE TWO-CHANNEL

POWER AMPLIFIER

AMPLIFICATEUR DE PUISSANCE

PONTABLE A DEUX VOIES

Owner’s Manual

GM-3200T

Mode d’emploi

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN

Before Using This Product

Thank you for purchasing this PIONEER product. It is designed to give you many years of enjoyment.

PIONEER SUGGESTS USING A PRO- FESSIONAL INSTALLER DUE TO THE COMPLEXITY OF THIS PRODUCT. Please read all instructions and WARN- INGS in this manual before attempting operation. Should you have any questions, contact your nearest Pioneer authorized dealer or installation specialist.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

Important

The serial number of this amplifier is writ- ten on the bottom of the unit. For your own security and convenience, write it down on the enclosed warranty card. Keep the card handy for future reference.

After-sales service for Pioneer products

Please contact the dealer or distributor from where you purchased the product for its after-sales ser- vice (including warranty conditions) or any other information. In case the necessary information is not available, please contact the companies listed below:

Please do not ship your product to the companies at the addresses listed below for repair without advance contact.

7U.S.A.

Pioneer Electronics (USA) Inc.

CUSTOMER SUPPORT DIVISION P.O. Box 1760

Long Beach, CA 90801-1760 800-421-1404

7CANADA

Pioneer Electronics of Canada, Inc.

CUSTOMER SATISFACTION DEPARTMENT

300 Allstate Parkway Markham, Ontario L3R OP2 1-877-283-5901

For warranty information please see the Limited Warranty sheet included with your product.

Product registration

CAUTION

Never replace the fuse with one of greater value or rating than the original fuse. Use of an improper fuse could result in over- heating and smoke and could cause dam- age to the product and injury including burns.

CAUTION

Diagram A - Proper

Diagram B - Improper

 

8

 

4

 

+ Ohm -

 

+ Ohm -

 

Speaker

 

Speaker

 

8

 

4

 

+ Ohm -

 

+ Ohm -

 

Speaker

 

Speaker

L+

R-

L+

R-

 

Pioneer

 

Pioneer

 

Amplifier

 

Amplifier

4 Ohm Bridged Mode

2 Ohm Bridged Mode

Do NOT install or use your Pioneer ampli- fier by wiring speakers rated at 4 Ohm (or lower) in parallel to achieve a 2 Ohm (or lower) bridged mode (Diagram B). Amplifier damage, smoke, and overheating could result from improper bridging. The amplifier surface could also become hot to

<ENGLISH>

WARNING

• Handling the cord on this product or cords associ-

ated with accessories sold with the product will

expose you to lead, a chemical known to the State

of California and other governmental entities to

cause cancer and birth defects or other reproduc-

tive harm. Wash hands after handling.

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

• Do not touch the amplifier with wet hands.

Otherwise you may get an electric shock. Also, do

not touch the amplifier when it is wet.

• For traffic safety and to maintain safe driving

conditions, keep the volume low enough so that

you can still hear normal traffic sound.

• Check the connections of the power supply and

speakers if the fuse of the separately sold battery

wire or the amplifier fuse blows. Detect the cause

and solve the problem, then replace the fuse with

another one of the same size and rating.

• To prevent malfunction of the amplifier and

speakers, the protective circuit will cut the power

supply to the amplifier (sound will stop) when an

abnormal condition occurs. In such a case, switch

the power to the system OFF and check the

connection of the power supply and speakers.

Detect the cause and solve the problem.

• Contact the dealer if you cannot detect the cause.

• To prevent an electric shock or short-circuit

during connection and installation, be sure to

disconnect the negative (–) terminal of the battery

beforehand.

• Confirm that no parts are behind the panel when

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia TEL: (03) 9586-6300

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270

Published by Pioneer Corporation. Copyright © 2005 by Pioneer Corporation. All rights reserved.

Publication de Pioneer Corporation. Copyright © 2005 Pioneer Corporation. Tous droits de reproduction et de traduction réservés.

Printed in China

Imprimé en Chine

Visit us at the following site:

1Register your product. We will keep the details of your purchase on file to help you refer to this information in the event of an insurance claim such as loss or theft.

2Receive updates on the latest products and tech- nologies.

3Download owner’s manuals, order product cata- logues, research new products, and much more.

the touch and minor burns could result. To properly install or use a bridged mode for a two-channel amplifier and achieve a 4

load, wire two 8 speakers in parallel

with Left + and Right – (Diagram A) or use a single 4 speaker. For a four-chan- nel amplifier, follow the speaker output connection diagram for bridging as shown

on the back of your amplifier, and wire two 8 speakers in parallel to achieve a 4

load or use a single 4 speaker per channel.

If you have any questions or concerns, please contact your local authorized Pioneer dealer or call Pioneer customer service.

drilling a hole for installation of the amplifier. Be

sure to protect all cables and important equipment

such as fuel lines, brake lines and the electrical

wiring from damage.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

<KMINX> <05I00000>

<CRD4016-B/U> UC

Image 1
Contents After-sales service for Pioneer products Before Using This ProductEnglish Information to UserConnecting the Unit Setting the UnitSpecifications InstallationUsing the Speaker Input Connecting the Speaker WiresFrançais Avant d’utiliser cet appareilRéglage de l’appareil PrécautionConnexion des câbles des haut Raccordement de l’appareil’alimentation ParleursAntes de usar este producto Caractéristiques techniquesEspañol PrecaucionConexión de la unidad Ajuste de esta unidadEspecificaciones InstalaciónUso de la entrada de altavoz Conexión de los cables de altavoces