Sharp MD-MX10H To see the time display, To change the clock time, To change the time display mode

Page 10

Press the ON/STAND-BY button to turn the power on.

CLOCK

Jog dial

ON/STAND-BY

MEMORY/ ENTER

SETTING THE CLOCK

●In this example, the clock is set for the 24-hour (0:00) sys- tem.

1

2 Press the CLOCK button.

6 Adjust the hour by turning the jog dial.

●When the jog dial is turned one click clockwise, the time will increase by 1 hour. When it is turned one click anti- clockwise, the time will decrease by 1 hour.

Keep turning the jog dial to change the time continuously.

●When the 12-hour display is selected, “AM” will change automatically to “PM”.

7 Press the MEMORY/ENTER button.

8 Adjust the minutes by turning the jog dial.

●When the jog dial is turned one click clockwise, the time will increase by 1 minute. When it is turned one click anti- clockwise, the time will decrease by 1 minute.

Keep turning the jog dial to change the time continuously.

●The hour setting will not advance even if minutes advance from "59" to "00".

9 Press the MEMORY/ENTER button.

●The clock starts operating from "0" second. (Seconds are not displayed.)

3 Within 5 seconds, press the MEMORY/ENTER button.

4 Turn the jog dial to select the time display mode.

"0:00" →The 24-hour display will appear. (0:00 - 23:59)

"12:00 AM" →The 12-hour display will appear. (AM or PM 12:00 - 11:59)

"0:00 AM" →The 12-hour display will appear. (AM or PM 0:00 - 11:59)

●Note that this can only be set when the unit is first in- stalled or it has been reset (see page 36).

5 Press the MEMORY/ENTER button.

9

To see the time display:

Press the CLOCK button.

●The time display will appear for about 5 seconds even in the stand-by mode.

Note:

●The "CLOCK" will appear at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power lead is disconnected.

If this happens, follow the procedure below to change the clock time.

To change the clock time:

1Press the CLOCK button.

2Within 5 seconds, press the MEMORY/ENTER button.

3Perform steps 6 - 9 above.

To change the time display mode:

1Reset the microcomputer (see page 36).

2Perform steps 2 - 9 above.

Image 10

Contents Contents MD-MX10HService Information Special NotesAccessories PrecautionsNames of Controls and Indicators Front panelDisplay window Rear panelRemote control Speaker section Aerial connection Preparation for USESpeaker connection To cancel the demonstration mode Connecting the AC power leadDemo mode Placing the systemTo change the brightness of the display Remote controlDimmer To change the clock time To change the time display modeTo see the time display Press the MEMORY/ENTER buttonPre-programmed equalizer VolumeSound Control Extra bass X-BASSCompact Disc Operation CD playbackTo remove a MiniDisc Minidisc OperationMiniDisc playback Press the MD 06 buttonCue and review Convenient CD and Minidisc OperationsApss Auto Program Search System MD/CD 3 MD/CDCD H Apms Automatic Programmable Music SelectorClear CD H MD H Repeat and random play ModeTime Switching the time displayChanging the display during MiniDisc playback DisplayManual tuning Auto tuningPreset Preset tuningPreset memory scan Clear Memory EnterDisc writing TOC RecordingDifferences from tape recordings About track numbersTo check the remaining time available for record- ing To cancel the operationRecording from a CD onto a MiniDisc One-Touch Editing To stop recordingTrack editing from a CD onto a MiniDisc Press the REC button To record without using One-Touch EditingApms recording from a CD onto a MiniDisc Press the CD 06 buttonTo record the track number whilst recording Recording from the built-in radio onto a MiniDiscCheck the recordable time by pressing the Display button What the editing function can do TIMER/DELETEEditing To create a disc nameTo create a track name To erase a track nameJog dial To delete a character TIMER/DELETE NAME/TOC Edit 3 MD Memory EnterTo change disc names and track names To add a characterTwo consecutive tracks can be combined into one track When both tracks have a nameDivide Combine Press the MEMORY/ENTER button againTo combine two non-contiguous tracks MoveDesignated track can be moved to any desired position To erase tracks one at a time Erase All EraseTracks you want to erase can be erased one at a time All of the tracks you want to erase can be erased at onceJog dial 2 CD H Timer OperationTimer playback/Timer recording Tuner Band 2 AUXSleep operation Simultaneous sleep and timer operationSTAND-BY Connecting external units Using External UnitsHeadphones Listening to sound from an external unit Manual recordingWhat is a MINIDISC? Minidisc System Limitations TroubleshootingIf a problem occurs GeneralMiniDisc recording and playback Resetting the MicrocomputerRemote control Radio receptionSymbol Error MessagesError messages Meaning Remedy Number orMaintenance SpecificationsTerms of Guarantee