Sharp MD-MX10H operation manual Special Notes, Service Information

Page 2

SPECIAL NOTES

NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used.

Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.

In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut-off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.

Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet as a serious electric shock may occur.

To fit an appropriate plug to the mains lead, follow the in- structions below:

IMPORTANT:

The wires in the mains lead are coloured in accordance with the following code:

Blue : Neutral

Brown : Live

Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three pin plug.

Before replacing the plug cover, make sure that:

If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.

The cord grip is clamped over the sheath of the mains lead and not simply over the lead wires.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELEC- TRICIAN.

SERVICE INFORMATION

In the unlikely event of your equipment requiring repair, please contact the dealer or supplier from whom it was pur- chased. Where this is not possible, please contact the tel- ephone number listed below.

You will then be given details of how to obtain service. - 0345-125387 -

Please note; all calls will be charged at local rate.

Certain replacement parts and accessories may be obtained from our main parts distributor.

WILLOW VALE ELECTRONICS LTD.

MANCHESTER 0161-682-1415

READING 01189-876444

As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.

The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.

In the unlikely event of this equipment requiring repair dur- ing the guarantee period, you will need to provide proof of the date of purchase to the repairing company.

Please keep your invoice or receipt, which is supplied at the time of purchase.

Recording and playback of any material may require con- sent, which SHARP is unable to give. Please refer particu- larly to the provisions of the Copyright Act 1956, the Dra- matic and Musical Performers Protection Act 1958, the Performers Protection Acts 1963 and 1972 and to any sub- sequent statutory enactments and orders.

This equipment complies with the requirements of Direc- tives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC.

US and foreign patents licensed from Dolby Laboratories Licensing Corporation.

When the ON/STAND-BY button is set at STAND-BY posi- tion, mains voltage is still present inside the unit.

When the ON/STAND-BY button is set at STAND-BY posi- tion, the unit may be brought into operation by the timer mode or remote control.

Warning:

This unit contains no user serviceable parts. Never remove covers unless qualified to do so. This unit contains danger- ous voltages, always remove mains plug from the socket before any service operation and when not in use for a long period.

Warning:

To prevent fire or shock hazard, do not expose this appli- ance to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus.

CAUTION

Use the MD compact component system only in accordance with the instructions given in this manual and do not attempt to interfere with the interlock switch or make any other adjust- ment as this may result in exposure to hazardous radiation.

1

Image 2
Contents Contents MD-MX10HService Information Special NotesAccessories PrecautionsNames of Controls and Indicators Front panelDisplay window Rear panelRemote control Speaker section Speaker connection Preparation for USEAerial connection To cancel the demonstration mode Connecting the AC power leadDemo mode Placing the systemDimmer Remote controlTo change the brightness of the display To change the clock time To change the time display modeTo see the time display Press the MEMORY/ENTER buttonPre-programmed equalizer VolumeSound Control Extra bass X-BASSCompact Disc Operation CD playbackTo remove a MiniDisc Minidisc OperationMiniDisc playback Press the MD 06 buttonCue and review Convenient CD and Minidisc OperationsApss Auto Program Search System MD/CD 3 MD/CDClear CD H MD H Apms Automatic Programmable Music SelectorCD H Repeat and random play ModeTime Switching the time displayChanging the display during MiniDisc playback DisplayManual tuning Auto tuningPreset Preset tuningPreset memory scan Clear Memory EnterDisc writing TOC RecordingDifferences from tape recordings About track numbersTo check the remaining time available for record- ing To cancel the operationRecording from a CD onto a MiniDisc One-Touch Editing To stop recordingTrack editing from a CD onto a MiniDisc Press the REC button To record without using One-Touch EditingApms recording from a CD onto a MiniDisc Press the CD 06 buttonCheck the recordable time by pressing the Display button Recording from the built-in radio onto a MiniDiscTo record the track number whilst recording What the editing function can do TIMER/DELETEEditing To create a disc nameTo create a track name To erase a track nameJog dial To delete a character TIMER/DELETE NAME/TOC Edit 3 MD Memory EnterTo change disc names and track names To add a characterTwo consecutive tracks can be combined into one track When both tracks have a nameDivide Combine Press the MEMORY/ENTER button againDesignated track can be moved to any desired position MoveTo combine two non-contiguous tracks To erase tracks one at a time Erase All EraseTracks you want to erase can be erased one at a time All of the tracks you want to erase can be erased at onceJog dial 2 CD H Timer OperationTimer playback/Timer recording Tuner Band 2 AUXSTAND-BY Simultaneous sleep and timer operationSleep operation Headphones Using External UnitsConnecting external units Listening to sound from an external unit Manual recordingWhat is a MINIDISC? Minidisc System Limitations TroubleshootingIf a problem occurs GeneralMiniDisc recording and playback Resetting the MicrocomputerRemote control Radio receptionSymbol Error MessagesError messages Meaning Remedy Number orMaintenance SpecificationsTerms of Guarantee