Sharp MD-MX10H Resetting the Microcomputer, MiniDisc recording and playback, Radio reception

Page 37

(Continued)

MiniDisc recording and playback

Symptom

Possible cause

Remedy

 

 

 

● A recording cannot be made.

● Is the MiniDisc protected against ac-

● Slide the accidental erase preven-

 

cidental erasure?

tion tab back to its original position.

 

● Did you try to make recording on a

● Replace it with a recordable disc.

 

playback-only MiniDisc?

● Put in another recordable disc with

 

 

 

● Can you see the "DISC FULL" or

recording space on it.

 

"TOC FULL" message in the display?

 

● Even though a disc has been loaded,

● The disc is very dirty.

● Clean the disc.

"NO DISC" or "CAN'T READ" is dis-

● Is the unit located near excessive vi-

● Place the unit on a firm, level sur-

played.

brations?

face free from vibration.

● Playback sounds are skipped.

● Has condensation formed inside the

● Remove the disc and leave the

 

 

unit?

power turned on. The unit should

 

 

function properly in about 1 hour.

Radio reception

Symptom

Possible cause

Remedy

 

 

 

● Radios make unusual noise con-

● The unit is placed near the TV or

● When the unit receives a radio

secutively.

computer.

broadcast near a TV set, a compu-

 

● The aerial direction is not placed

ter or a word-processor, it may pick

 

up noise. If this happens, move the

 

properly.

 

unit from the place where the noise

 

 

 

 

is picked up.

 

 

● Correct the aerial direction.

 

 

 

● The preset channel cannot be re-

● Did you erase the programmed sta-

● Preset the channel again.

called.

tion?

● Redo programming.

 

 

Remote control

Symptom

Possible cause

Remedy

 

 

 

● The remote control does not func-

● The batteries (polarity) are not in-

● Insert properly.

tion or does not operate properly.

serted properly.

● Replace the batteries.

 

● The batteries inside the remote con-

● Operate it within a range of 0.2 m

 

trol are dead.

(8") to 6 m (20') and within an angle

 

● The remote control is operated from

of 15 ° to either side of centre.

 

an incorrect distance or angle.

 

● The power cannot be turned on from

● Is the AC power lead plugged in?

● Connect the AC power lead.

the remote control.

 

 

 

 

 

RESETTING THE MICROCOMPUTER

2

1,2

2

If this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal sup- ply voltage due to lightning, etc.) or if it is operated incor- rectly, it may malfunction or the display may not function cor- rectly. If such a problem occurs, do the following:

1 Press the ON/STAND-BY button to enter the stand-by mode.

2 Press the ON/STAND-BY button whilst holding down the SURROUND button and the TIMER/DELETE but- ton.

●"ALL CLEAR" will appear.

Caution:

●The operation explained above will erase all data stored in memory including clock and timer settings, and tuner, MiniDisc and CD presets.

36

Page 36 Page 38
Image 37
Page 36 Page 38
Contents MD-MX10H ContentsSpecial Notes Service InformationPrecautions AccessoriesFront panel Names of Controls and IndicatorsRear panel Display windowRemote control Speaker section Aerial connection Preparation for USESpeaker connection Demo mode Connecting the AC power leadTo cancel the demonstration mode Placing the systemTo change the brightness of the display Remote controlDimmer To see the time display To change the time display modeTo change the clock time Press the MEMORY/ENTER buttonSound Control VolumePre-programmed equalizer Extra bass X-BASSCD playback Compact Disc OperationMiniDisc playback Minidisc OperationTo remove a MiniDisc Press the MD 06 buttonApss Auto Program Search System Convenient CD and Minidisc OperationsCue and review MD/CD 3 MD/CDCD H Apms Automatic Programmable Music SelectorClear CD H MD H Mode Repeat and random playChanging the display during MiniDisc playback Switching the time displayTime DisplayAuto tuning Manual tuningPreset memory scan Preset tuningPreset Clear Memory EnterDifferences from tape recordings RecordingDisc writing TOC About track numbersRecording from a CD onto a MiniDisc One-Touch Editing To cancel the operationTo check the remaining time available for record- ing To stop recordingTrack editing from a CD onto a MiniDisc Apms recording from a CD onto a MiniDisc To record without using One-Touch EditingPress the REC button Press the CD 06 buttonTo record the track number whilst recording Recording from the built-in radio onto a MiniDiscCheck the recordable time by pressing the Display button Editing TIMER/DELETEWhat the editing function can do To create a disc nameTo erase a track name To create a track nameTo change disc names and track names TIMER/DELETE NAME/TOC Edit 3 MD Memory EnterJog dial To delete a character To add a characterDivide Combine When both tracks have a nameTwo consecutive tracks can be combined into one track Press the MEMORY/ENTER button againTo combine two non-contiguous tracks MoveDesignated track can be moved to any desired position Tracks you want to erase can be erased one at a time Erase All EraseTo erase tracks one at a time All of the tracks you want to erase can be erased at onceTimer playback/Timer recording Timer OperationJog dial 2 CD H Tuner Band 2 AUXSleep operation Simultaneous sleep and timer operationSTAND-BY Connecting external units Using External UnitsHeadphones Manual recording Listening to sound from an external unitWhat is a MINIDISC? If a problem occurs TroubleshootingMinidisc System Limitations GeneralRemote control Resetting the MicrocomputerMiniDisc recording and playback Radio receptionError messages Meaning Remedy Error MessagesSymbol Number orSpecifications MaintenanceTerms of Guarantee
Top Page Image Contents