Pioneer AVH-P7850DVD Installing the hide-away unit, DIN Front/Rear-mount, DIN Front-mount

Installation

Note:

•Before making a final installation of the unit, temporarily connect the wiring to confirm that the connections are correct and the system works properly.

•Use only the parts included with the unit to ensure proper installation. The use of unautho- rized parts can cause malfunctions.

•Consult with your nearest dealer if installation requires the drilling of holes or other modifica- tions of the vehicle.

•Install the unit where it does not get in the dri- ver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

•Do not place the display in a position where it will impede the driver’s visibility or affect the operation of your vehicle’s air bags.

•The semiconductor laser will be damaged if it overheats, so don’t install the unit anywhere hot

— for instance, near a heater outlet.

•If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance. (Fig. 8)

30°

Fig. 8

•When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.

•The cords must not cover up the area shown in the figure below. This is necessary to allow the amplifires to radiate freely. (Fig. 9)

Do not close this area.

Fig. 9

15

•When mounting the hide-away unit, make sure none of the leads are trapped between the hide- away unit and the surrounding metalwork or fit- tings.

•Do not mount the hide-away unit near the heater outlet, where it would be affected by heat, or near the doors, where rainwater might splash onto it.

•Before drilling any mounting holes always check behind where you want to drill the holes. Do not drill into the gas line, brake line, electrical wiring or other important parts.

•If the hide-away unit is installed in the passenger compartment, anchor it securely so it does not break free while the car is moving, and cause injury or an accident.

•If the hide-away unit is installed under a front seat, make sure it does not obstruct seat move- ment. Route all leads and cords carefully around the sliding mechanism so they do not get caught or pinched in the mechanism and cause a short circuit.

Installing the hide-away unit

Mounting with Brackets

Tapping screw (4 ⋅ 12 mm)

Carmat or chassis	Screw
Bracket
	(4 ⋅ 8 mm)

Drill 2 to 2.5 mm diameter holes.

Fig. 10

Mounting with Velcro Tape

Thoroughly wipe off the surface before affixing the velcro tape.

Hide-away unit

Velcro tape (large) (hard)

Velcro tape (large) (soft)

Car mat or chassis

Fig. 11

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear- mount installation, utilizing threaded screw holes at the sides of unit chas- sis). For details, refer to the following illustrated installation methods.

Before installing the unit

•Remove the frame and the hold- er. (Fig. 12)

Pull out to remove the frame and then loosen the screws (2 ⋅ 3 mm) to remove the holder. (When reattaching the frame, point the side with a groove downwards and attach it.)

Holder

Screw (2 ⋅ 3 mm)

Frame

Fig. 12

DIN Front-mount

Installation with the rubber bush	English
1. Decide the position of the side
brackets. (Fig. 13)
When installing in a shallow space,	Español
change the position of side brackets. In
this case, stick conceal tape on parts
that protrude from the dashboard.
	Deutsch
Conceal tape	Français
Side bracket
Flush surface screw (5 ⋅ 6 mm)
Fig. 13
	Italiano
	Nederlands
	PyÒÒÍËÈ

16