Appendix
Symptom | Cause | Action (See) | |||
| Setting of the Installation direction | Check the installation position of the | |||
| lever is wrong. | navigation unit of your Navigation | |||
|
| System and the setting of the Instal- | |||
|
| lation direction lever (➞ “Installation | |||
|
| Manual”). |
| ||
|
|
|
|
| |
| Indication of the position of your | Check whether or not the reverse | |||
| vehicle is misaligned after a | gear signal input lead (purple) is con- | |||
| reversing. | nected properly. (The Navigation Sys- | |||
|
| tem works properly without the lead | |||
|
| connected, but positioning accuracy | |||
|
| will be adversely affected.) | |||
The map continually reorients itself. | The traveling direction is always set | Touch |
|
| on the screen and change |
| |||||
| to north. | the map | display. | ||
Tracking marks are not displayed. | The “Tracking Display” is turned | Check the “Tracking Display” set- | |||
| off. | tings (➞ Page 48) and make sure | |||
|
| “Always” or “This Trip” is selected. | |||
|
|
|
|
| |
The daylight display is used even | Daytime is selected on “Day/Night | Check the “Day/Night Display” set- | |||
when the vehicle lights are on. | Display”. | ting (➞ Page 48) and make sure | |||
|
| “Nighttime” is selected. | |||
|
|
|
|
| |
| The Orange/white lead is not con- | Check the connection. | |||
| nected. |
|
|
|
|
|
|
|
|
| |
The system will not switch on or will | Installation or connection has been | Check with your dealer. | |||
not operate. | carried out incorrectly. |
|
|
|
|
|
|
|
|
| |
The display is very dim. | The vehicle’s light is turned ON, and | Read about the “Day/Night Dis- | |||
| “Nighttime” is selected on “Day/ | play” setting (➞ Page 48) and, if | |||
| Night Display”. | desired, select “Daytime”. | |||
| The vehicle cabin temperature is | A Liquid Crystal Display (LCD) is | |||
| extremely low. | used, and such displays tend to | |||
|
| darken when cold. Wait for the vehi- | |||
|
| cle to warm up. | |||
|
|
|
|
| |
There is no voice guidance or the vol- | The volume setting is low or the | Check the volume setting on the dis- | |||
ume is low. | speaker lead is disconnected. | play or turn the volume up according | |||
|
| to “Hardware Volume” (➞ Page 48) | |||
|
| and/or turn up the volume on the dis- | |||
|
| play. |
| ||
|
|
|
|
| |
The Remote Control fails to work. | The batteries are low. | Change the batteries. | |||
| The batteries have been inserted | Check that the batteries are properly | |||
| incorrectly. | inserted according to the + and – | |||
|
| markings. |
| ||
|
|
|
|
| |
| The Remote Control is pointing at the | Ensure that the Remote Control has | |||
| floor or a seat. | a clear line of sight to the display | |||
|
| unit. |
| ||
| The signal receptor on the display is | Move the Remote Control closer to | |||
| exposed to direct sunlight. | the receiver on the display unit. |
When the screen is frozen...
Park your vehicle at a safe place, and cut the engine off. Turn the ignition key back to “Acc off”. Then start the engine again, and turn the power to the main unit back on. If this does not solve the prob- lem, press the Reset button on the main unit.
62