6WARNING | |
• | If you connect the ignition wire (red) and the |
| battery wire (yellow) to the car chassis (ground), |
| you may cause a short circuit, that in turn may |
| start a fire. Always connect those wires to the |
| power source running through the fuse box. |
• | Do not cut out the fuse from the ignition wire (red) |
| and the battery wire (yellow). The power supply |
| must be connected to the wires via the fuse. |
6 | Precautions on installation and connection |
• | Mounting and wiring this product requires |
| skills and experience. For best safety, leave the |
| mounting and wiring work to professionals. |
• | Make sure to ground the unit to a negative 12 V |
| DC power supply. |
• | Do not install the unit in a spot exposed to direct |
| sunlight or excessive heat or humidity. Also avoid |
| places with too much dust or the possibility of |
| water splashing. |
• | Do not use your own screws. Use only the screws |
| provided. If you use the wrong screws, you could |
| damage the unit. |
• | If the power is not turned on ("MISWIRING Check |
| wiring connection then reset unit", "WARNING |
| Check wiring connection then reset unit" is |
| displayed), the speaker wire may have a short |
| circuit or have touched the chassis of the vehicle |
| and the protection function may have been |
| activated. Therefore, the speaker wire should be |
| checked. |
• | If your car'signition does not have an ACC |
| position, connect the ignition wires to a power |
| source that can be turned on and off with the |
| ignition key. If you connect the ignition wire to a |
| power source with a constant voltage supply, such |
| as with battery wires, the battery may be drained. |
• | Only for |
| If the console has a lid, make sure to install the |
| unit so that the monitor panel will not hit the lid |
| when closing and opening. |
• | If the fuse blows, first make sure the wires are not |
| touching to cause a short circuit, then replace the |
| old fuse with one with the same rating. |
• | Insulate unconnected wires with vinyl tape or |
| other similar material. To prevent a short circuit, |
| do not remove the caps on the ends of the |
| unconnected wires or the terminals. |
• | Connect the speaker wires correctly to the |
| terminals to which they correspond. The unit may |
| be damaged or fail to work if you share the 8 |
| wires or ground them to any metal part in the car. |
• | When only two speakers are being connected to |
| the system, connect both connectors either to |
| the front output terminals or to the rear output |
| terminals (do not mix front and rear). For example, |
| if you connect the E8 connector of the left speaker |
| to a front output terminal, do not connect the 8 |
| connector to a rear output terminal. |
• | After the unit is installed, check whether the brake |
| lamps, blinkers, wipers, etc. on the car are working |
| properly. |
• | Mount the unit so that the mounting angle is 30° |
| or less. |
• | Do not press hard on the panel surface when |
| installing the unit to the vehicle. Otherwise scars, |
| damage, or failure may result. |
&CAUTION Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during and shortly after the use of the unit. Metal parts such as the heat sink and enclosure become hot.
0 Supplied accessories for installation | |||||
CD | Wiring harness x | 1 |
| ||
(%) | Trim plate x 1 * | 1 |
|
| |
|
|
| |||
® | Extension wire x | 1 |
| ||
® | Extraction keys x 2 * | 1 | |||
| |||||
® | Flat head screws | (MS x 7 mm) x 6 | |||
® | Round head screws | (MS x 6 mm) x 6 | |||
(]) |
|
| 2 |
| |
Microphone x 1 * |
| ||||
* | 1 | Only for | |||
* |
| 4. |
|
|
|
2 | Only for |
ENGLISH
I
49