Powermatic HPS67 operating instructions Sliding Table Lock, Crosscut Fence

Page 15

When bevel cutting, make sure the appropriate blade guard has been mounted before operating the saw.

Sliding Table Lock

When loading panels and when cutting using the rip fence, the sliding table should be locked.

To lock the sliding table, pull lever (Figure 24) into one of the slots in the sliding table.

Over a long period of time, if many short movements of the sliding table are made (e.g. crosscutting solid wood) then it is possible that the ball carrier between the upper and lower part of the sliding table will move. This means it will no longer be correctly positioned to allow the sliding table to slide through its full course. The operator will feel resistance in the sliding table motion and the full stroke will not be achieved. This effect can be corrected simply by pushing the table with a few short, light pushes against the buffer stop at the end, until the position of the ball carrier is adjusted and the table can be moved again along its full stroke.

Crosscut Fence

The 90-degree angle of the fence is factory set. However, should adjustment ever be needed, proceed as follows:

1.Loosen the two bolts (A, Figure 25).

2.Turn bolt (B, Figure 25) to open or close the angle of the fence in relation to the saw blade.

3.Re-tighten bolts (A, Figure 25).

Before using the first time, and each time a new blade is installed, the scales must be calibrated. Proceed as follows:

1.Put the stop (Figure 26) at a certain measure and cut off a sample.

2.Measure the exact length of the sample. Loosen the screw (Figure 26) which holds the scale and move the scale until the measurement corresponds to the length of the previously cut sample. The main part of the fence is now calibrated to the saw blade.

3.The scale on the telescopic extension of the fence should now be checked and adjusted. Move the other stop to the outermost edge of the extension fence until the edge of the stop is flush with the edge of the fence (Figure 27). Lock the stop in position by tightening the handle.

NOTE: DO NOT loosen the stop until the adjustment procedure has been completed.

Figure 24

Figure 25

Figure 26

Figure 27

15

Image 15
Contents Part No. M-0460273 Horizontal Panel SawMore Information Warranty and ServiceTable of Contents Page Page HPS67 Introduction SpecificationsMachine Dimensions Installation and Assembly Contents of crateUnpacking Installing Extension Tables Installing Crosscut TableInstalling Crosscut Fence Installing Blade Guard Installing Guide BarInstalling Rip Fence Installing Over ArmInstalling Miter Fence Installing/Replacing Main BladeElectrical Connections Riving Knife Installing/Replacing Scoring BladeStarting the Machine Dust CollectionDo not remove the riving knife for saw operations Setting Blade Guard AdjustmentsSetting Main Blade Figures 21 Setting Scoring BladeCrosscut Fence Sliding Table LockWood Cap Miter Fence Rip FenceRip Fence Scale Calibration Tensioning the Belt Precision Tuning Your Panel SawFree Cut Blade to Sliding Table Symptoms of positive free cutSymptoms of negative free cut Free Cut Blade to Rip FenceTo correct the free cut Operation Square CutScoring Blade Maintenance Troubleshooting TroubleProbable Cause Remedy Optional Accessories Replacement PartsTrouble Probable Cause Remedy Index No. Part No Description Size Qty Parts List Motor and Arbor AssemblyTS-1490031 Motor and Arbor Assembly Parts List Scoring Motor and Arbor Assembly Page Parts List Stand and Table Assembly TS-1540031 Parts List Support Arm Assembly Support Arm Assembly Parts List Cross Cut Fence Assembly Cross Cut Fence Assembly Parts List Rip Fence Assembly Rip Fence Assembly TS-1524021 Parts List Over Arm Guard AssemblyOver Arm Guard Assembly Parts List Sliding Table Assembly Page Sliding Table Assembly Parts List Electrical Components 3 Phase Parts List Electrical Components 1 PhaseIndex No. Part No Description Qty Electrical Connections 3 Phase Electrical Connections 1 Phase Page Page WMH Tool Group
Related manuals
Manual 6 pages 26.75 Kb

HPS67 specifications

The Powermatic HPS67 is an innovative and powerful hybrid table saw that epitomizes precision woodworking. Designed for serious woodworkers and professionals, the HPS67 integrates advanced technologies and features that elevate its performance and usability in the workshop.

At the heart of the HPS67 lies its robust motor, offering a remarkable power output that facilitates seamless cutting through a variety of materials, including hardwoods and composite materials. The saw’s rip capacity is impressive, allowing users to cut wide panels with ease and precision. Its well-engineered design supports both rip cuts and crosscuts, making it versatile for different woodworking projects.

One of the standout features of the Powermatic HPS67 is its advanced dust collection system. The saw is equipped with an efficient dust port that captures debris during cutting, ensuring a clean workspace and promoting a healthier environment for users. This system reduces the overall cleanup time and increases visibility while working.

The HPS67 incorporates an innovative digital display that provides real-time feedback on blade height and angle adjustments. This feature allows for precise settings, ensuring that users can achieve the exact cuts they desire consistently. The easy-to-read display enhances the overall user experience, making it simpler to make quick adjustments on the fly.

Furthermore, the HPS67 boasts a large, sturdy table surface that offers ample support for large sheets of wood. The tabletop is made from high-quality cast iron, known for its durability and stability. This material minimizes vibrations during operation, thus contributing to the saw's accuracy.

Safety is paramount with the Powermatic HPS67, which features a comprehensive set of safety guards and notifications. The blade guard is designed for easy removal and replacement, ensuring that operators can maintain safety without hindrance to workflow. Additionally, the built-in safety features minimize the risk of accidents, providing peace of mind for woodworkers.

In summary, the Powermatic HPS67 is a sophisticated hybrid table saw that combines power, precision, and safety. Its exceptional features, advanced technologies, and user-focused design make it an invaluable addition to any woodworking shop. Whether for professional use or serious hobbyists, the HPS67 empowers users to take on a variety of woodworking projects with confidence and efficiency.