ACR Electronics ZE-NES14 user manual Device Connections

Page 39

ZE-NC514

DEVICE CONNECTIONS

NOTES OF CONNECTION

■This unit is designed to be used in a vehicle with a 12-volt battery and negative grounding. Before installing this unit to a mobile home, a bus, or a truck, make sure the battery voltage is appropriate for this unit to be used, otherwise, install a transformer to convert the output voltage to 12 V.

■To avoid short circuit in the electrical system, ensure that the negative battery cable is disconnected before installation.

■To prevent short circuit in the wiring and damaging to this unit, secure all wirings with cable ties or adhesive tape. Route the wirings in a secured, out of heating place without touching any moving parts such as gear shift, handbrake, and seat rails to prevent the wiring insulation being melted/wore off.

■Never pass the yellow power cord through the installation hole into the engine compartment and connect to the car battery. Otherwise, a high possibility of serious short circuit to the electrical system may occur.

■Replacing a new fuse with 10 A rating when the old one is broken, using no fuse or fuse with improper rating may cause damage to this unit or even fires. lf a proper fuse is installed and electrical problems still occur, please contact with any professional car shops for inquiry.

■Please make sure all the wiring connections and the cables of the speakers are well- insulated. Otherwise, this unit may be damaged by short circuit.

■lf there is no ACC available, please connect ACC lead to the power supply with a swit ch.

■lf an external power amplifier is connected, please don't connect P.CONT lead to the power lead of the external power amplifier, otherwise, electric spark or other damage may be resulted.

■Never ground the speaker output to prevent the damage to the built-in power amplifier.

■The minimum rating of the speakers connected to this unit is 50 W with 4 to 8 Ω impedance.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Model N0 Contents ZE-NC514 Page Declaration PrecautionsBefore Using Front PanelAV-IN jack USB Slot Auxiliary LCD Disc indicatorRepeat mode indicator Radio status indicatorsTilt Remote ControlInstall Battery Uninstall BatteryBasic Operations Using the TFT Monitor Reset the UnitDisplay System Time Radio Mode Local Seeking Manual SavePreview Scan Recall the Stored StationsRDS Operations AF FunctionTA Function RT Radio Text Program Service PSPTY Function CT Clock TimeTouch Screen Controls Disc ModeInsert a Disc Eject the DiscPBC Onscreen Control ButtonsFast Playback Suspend PlaybackStop Playback Display File ListRepeat Playback Repeat A-BRandom Playback Intro Playback Direct SearchGoto Search Select Audio Channel DVD Menu and TltleSelect Subtitle Language Select MULTI-ANGLE ViewsFor DVD Zoom IN/OUTRotate Picture Playback InformationFor VCD Select USB AS Playing Source USB ModeChange Folder Photo Playback Ipod ModeSelect Ipod AS Playing Source Music PlaybackVideo Playback Search Channel DVB-T ModeSelect DVB-T AS Playing Source Quick SelectOther Modes AV-INCamera Select one item SetupSetup Procedures 1. Enter setup mode Select one sub-menuLanguage OSD GeneralRating Audio DRCRDS TA VOLProcedures of Changing the Rating Method of Changing PasswordVOL HardwarePlease Note SourceLevel Method of Changing PasswortAdjust Front/Rear/Left/Right fader and balance Enter the EQ setup modeSelect EQ mode Adjust EQ parametersTroubleshooting Troubleshooting Device Connections Reverse Driving Control CablesAuto Brightness Control Telephone MuteGearbox Unit Installation Installation and UninstallationMethod B Disassemble the Unit Trim Ring InstallationUninstall Disassemble trim ringAudio SpecificationsGeneral DVD PlayerEnvironment VideoTFT Monitor NavigationRegion Code Do not use irregular shaped disc Disc CleaningWhen playing a new disc AppendixWiring Connections Years Limited Warranty Warranty LimitationsZenec Model ZE-NC514 Zenec by ACR AG · Bohrturmweg 1 · Bad Zurzach · Switzerland
Top Page Image Contents