AMX VTM-D15/A instruction manual Setting up the Panel, Mounting the TPI/3 in an equipment rack

Page 16

Installation and Wiring

2.Discharge the static electricity from your body by touching a grounded metal object.

3.Disconnect any other connectors from the TPI/3 input module.

4.Remove (counter-clockwise) the two black thumbscrews on the input module.

5.Slide the module out of the enclosure.

6.Repeat steps 4 and 5 for other slots, as required.

7.Ensure that all thumbscrews are secured and reconnect all rear panel connectors.

Mounting the TPI/3 in an equipment rack

Use the supplied mounting brackets for 19" equipment rack installations. Remove the mounting brackets for flat surface installations. You will need a Phillips screwdriver to install the TPI/3.

To install the AXB-TPI/3 in an equipment rack:

1.Discharge the static electricity from your body by touching a grounded metal object.

2.Install the mounting brackets using the screws supplied with the unit, as shown in FIG. 6.

FIG. 6 Installing mounting brackets

3.With the rack mount brackets installed, place the AXB-TPI/3 into the equipment rack, and align the mounting bracket holes with the mounting holes on the equipment rack. Start the mounting screws on both sides of the controller and tighten.

4.Thread the incoming AXlink, power cable (optional) and VTM-D15/A (DB-15 video and Touch Screen signal cables) through the opening in the equipment rack. Refer to the Configuration and Setup section on page 23 for more detailed information.

Setting up the Panel

The setup of the MultiMedia Touch Panel involves unpacking the unit, attaching the particular type of panel support (Table Top or Surface Mount), and connecting the appropriate cables.

1.Remove the panel from the shipping case.

2.Lay the back of the panel on a flat surface.

3.Remove the dust-proof plastic sheet (FIG. 7) from the screen (if applicable).

 

12

VTM-D15/A 15" MultiMedia Touch Panel Systems

 

 

 

Page 15 Page 17
Image 16
Page 15 Page 17
Contents VTM-D15/A AMX Limited Warranty and Disclaimer Table of Contents Upgrading the TPI/3 Firmware MultiMedia Touch Panel MultiMedia System ComponentsPower Adapter Power CordPin DB15 VGA Signal Cable Pin Mini Din to 9-pin DB9 Touch Panel Signal CableVTM-D15/A and VTM-D15/AB Specifications SpecificationsPSN6.5 Power Supply optional Floppy DiskIBM VGA VTM-D15/A and VTM-D15/AB Rear Components Rear component connection locations on the VTM-D15/ADimensions HWD AXB-TPI/3 SpecificationsFront Panel Rear Panel Components SendCommands AXB-TPI/3 Components RgbhvVTM-D15/A Sample Configuration Pin captive-wireInstallation and Wiring Setting up the AXB-TPI/3Installing the input modules Removing input modulesSetting up the Panel Mounting the TPI/3 in an equipment rackTable Top Installation VTM-D15/A and D15/AS Installing the Table Top support bracketFixing holes on each side of pull-out flap Connecting the cables on a VTM-D15/A table top panel Surface Mount Installation VTM-D15/AB and D15/ASBInstalling the Surface Mount support bracket Surface Mounting Kit VTM-WMB contents Connecting the cables on a VTM-D15/AB surface mount panel Rear of VTM-D15/AB shown with attached VTM-WMB bracketWiring the AXB-TPI/3 Preparing captive wiresWiring guidelines Using the AXlink connector for data and powerConnecting the MultiMedia Components Using the VGA in DB-15 male high-density connectorVGA in DB-15 Connector Pinouts Pin Signal FunctionYour system is now connected and receiving power Installation and Wiring VTM-D15/A Startup and Setup Procedures Configuration and SetupFront Panel buttons and indicators LEDs Setting Up Serial procedures Setting Up Serial Communication from PC to the TPI/3Using Axcessx for serial communication Using HyperTerminal for serial communication COM Port Parameter SettingsParameter Setting Setting up the VTM-D15/A touch device Setting the Output Resolution Available ResolutionsResolution Refresh Rates Supported Touch DevicesSetting Up AXlink procedures Setting Up AXlink Communication from Master to the TPI/3Calibrating the Monitor Using HyperTerminal for AXlink communication Using Axcessx for AXlink communicationSetting up the VTM-D15/A touch device through AXlink Setting Up NetLinx Communication from PC to the TPI/3 Use the following command to set the mouse driverSet the Output resolution of the TPI/3 by entering Using NetLinx Studio for communication via an COM Port SendCommand 130,’calibrate’ Configuration and Setup Upgrading the TPI/3 Firmware ConfigurationDownloading the Firmware Press F10 to exit the SoftROM program On Screen Display OSD Icons On Screen Display OSD FeaturesOn Screen Display OSD Icons Exiting the OSD Selecting the Language of the OSDAdjusting Screen Brightness and Contrast Adjusting Display Performance Phase and ClockAdjusting Horizontal and Vertical Screen Position Selecting the Picture Color TemperatureAdjusting Display Color Red, Green, Blue Adjusting OSD Menu Parameters OSD Position and TimerAdjusting the Picture Sharpness Adjusting the OSD Timer settingAutomatic Contrast Adjustment Optimizing Picture Performance in DOS Graphic/TextReturning Recall to Factory Default Settings Display Troubleshooting TroubleshootingTroubleshooting Use these messages to address panel issues Troubleshooting VTM-D15/A 15 MultiMedia Touch Panel Systems 12/02
Related manuals
Manual 52 pages 36.75 Kb

VTM-D15/A specifications

The AMX VTM-D15/A is a next-generation armored vehicle designed for versatility and adaptability in modern combat scenarios. Developed to meet the evolving demands of modern military operations, it embodies advanced technologies and exceptional characteristics that make it a standout choice for armed forces worldwide.

At the heart of the AMX VTM-D15/A is its robust chassis, designed to withstand harsh terrains and explosive devices. The vehicle boasts a well-protected hull using advanced composite materials and ballistic plating, ensuring crew safety in hostile environments. It can be fitted with reactive armor systems that enhance protection against projectiles and anti-tank missiles.

The VTM-D15/A features a powerful engine that provides high mobility across various landscapes, capable of reaching speeds of up to 100 km/h on flat terrain. Its off-road capabilities are complemented by a sophisticated suspension system that allows for excellent maneuverability in rugged conditions. The vehicle is also equipped with all-terrain tires, further enhancing stability and traction.

One of the remarkable aspects of the AMX VTM-D15/A is its modular design that allows for quick configuration changes between various combat roles. This adaptability permits the integration of different weapon systems, including machine guns and anti-tank guided missiles, that can be rapidly mounted or dismounted as per operational requirements.

The vehicle's advanced battlefield management system improves situational awareness, allowing for real-time data sharing and communication with other units. It is equipped with state-of-the-art sensors and reconnaissance tools, ensuring that it can gather intelligence and operate effectively in diverse combat environments.

Moreover, the AMX VTM-D15/A emphasizes crew comfort and ergonomics, featuring a spacious interior designed for extended missions. The vehicle's climate control systems and noise-reduction technologies significantly enhance crew endurance and focus in prolonged operations.

In a world where military operations are increasingly dynamic, the AMX VTM-D15/A stands out as a versatile, powerful, and technologically advanced armored vehicle. Its combination of protection, mobility, and adaptability ensures that it can meet a wide array of mission requirements, making it a vital asset in modern military arsenals.
Top Page Image Contents