AMX VTM-D15/A instruction manual MultiMedia Touch Panel, MultiMedia System Components

Page 5

MultiMedia Touch Panel

MultiMedia Touch Panel

The MultiMedia Touch Panel System (VTM-D15/A) comes ready-to-install and ready-to-use, the MultiMedia system comes in different types of configurations:

VTM-D15/A

• 15" Table Top MultiMedia Touch Panel

VTM-D15/AB

• 15" Surface Mount MultiMedia Touch Panel

VTM-D15/AS

• 15" Table Top System:

 

VTM-D15/A, AXB-TPI/3, and TP3-VID

VTM-D15/ASB

• 15" Surface Mount System:

 

VTM-D15/AB, AXB-TPI/3, TP3-VID, and VTM-WMB

The VTM-D15/A provides an impressive blend of vivid color graphics, sharp icons and seamless video. The TPD3-VID Video Module allows you to input different video sources, such as VCRs, Satellites, and DVDs into the TPI/3. The AXB-TPI/3 has three slots on the rear panel that can contain any combination of three types of input modules: Composite video/S-video (TP3-VID), RGB (TP3-RGB), and VGA (TP3-VGA). The touch input works via a serial device, such as a serial mouse or touch monitor. This system can be expanded by purchasing additional TPI/3 modules such as the TP3-VGA (Graphics), TP3-RGB (RGB input), and additional TP3-VID cards. The TPI/3 allows the use of any combination of three cards.

MultiMedia System Components

VTM-D15/A 15" MultiMedia Touch Panel

Available in Table Top (VTM-D15/A) or Surface/Wall Mount (VTM-D15/AB) versions. This touch panel has a wide viewing angle of up to 160 degrees, crisp color with quality depth/con- trast, and an enhanced touch screen overlay. Receives a VGA signal through either a Composite or S-Video connector port on the TP3-VID.

AXB-TPI/3 Touch Panel Interface 3

The unit sends graphics to a touch panel of your choice. The TPI/3 supports up to three scalable windows, which are driven by plug-in cards for video and computer graphics. The MultiMedia system comes pre-installed with a TP3-VID Video Module.

TP3-VID VIdeo Input Module

This input card provides Composite and S-Video connector ports that can be used to input a variety of video formats from different video sources. The TPI/3 comes with three available module slots, by installing a TP3-VID card, this leaves two other input slots available for use. With additional modules, you can mix and match any combination of input cards.

Cont.

VTM-D15/A 15" MultiMedia Touch Panel Systems

1

 

 

 

 

Image 5
Contents VTM-D15/A AMX Limited Warranty and Disclaimer Table of Contents Upgrading the TPI/3 Firmware MultiMedia System Components MultiMedia Touch PanelPower Cord Power AdapterPin DB15 VGA Signal Cable Pin Mini Din to 9-pin DB9 Touch Panel Signal CableSpecifications VTM-D15/A and VTM-D15/AB SpecificationsPSN6.5 Power Supply optional Floppy DiskIBM VGA Rear component connection locations on the VTM-D15/A VTM-D15/A and VTM-D15/AB Rear ComponentsFront Panel AXB-TPI/3 SpecificationsDimensions HWD Rear Panel Components SendCommands Rgbhv AXB-TPI/3 ComponentsPin captive-wire VTM-D15/A Sample ConfigurationSetting up the AXB-TPI/3 Installation and WiringInstalling the input modules Removing input modulesMounting the TPI/3 in an equipment rack Setting up the PanelInstalling the Table Top support bracket Table Top Installation VTM-D15/A and D15/ASFixing holes on each side of pull-out flap Installing the Surface Mount support bracket Surface Mount Installation VTM-D15/AB and D15/ASBConnecting the cables on a VTM-D15/A table top panel Surface Mounting Kit VTM-WMB contents Rear of VTM-D15/AB shown with attached VTM-WMB bracket Connecting the cables on a VTM-D15/AB surface mount panelPreparing captive wires Wiring the AXB-TPI/3Using the AXlink connector for data and power Wiring guidelinesUsing the VGA in DB-15 male high-density connector Connecting the MultiMedia ComponentsVGA in DB-15 Connector Pinouts Pin Signal FunctionYour system is now connected and receiving power Installation and Wiring Front Panel buttons and indicators LEDs Configuration and SetupVTM-D15/A Startup and Setup Procedures Using Axcessx for serial communication Setting Up Serial Communication from PC to the TPI/3Setting Up Serial procedures Parameter Setting COM Port Parameter SettingsUsing HyperTerminal for serial communication Setting up the VTM-D15/A touch device Available Resolutions Setting the Output ResolutionResolution Refresh Rates Supported Touch DevicesCalibrating the Monitor Setting Up AXlink Communication from Master to the TPI/3Setting Up AXlink procedures Setting up the VTM-D15/A touch device through AXlink Using Axcessx for AXlink communicationUsing HyperTerminal for AXlink communication Use the following command to set the mouse driver Setting Up NetLinx Communication from PC to the TPI/3Set the Output resolution of the TPI/3 by entering Using NetLinx Studio for communication via an COM Port SendCommand 130,’calibrate’ Configuration and Setup Downloading the Firmware ConfigurationUpgrading the TPI/3 Firmware Press F10 to exit the SoftROM program On Screen Display OSD Icons On Screen Display OSD FeaturesOn Screen Display OSD Icons Selecting the Language of the OSD Exiting the OSDAdjusting Display Performance Phase and Clock Adjusting Screen Brightness and ContrastSelecting the Picture Color Temperature Adjusting Horizontal and Vertical Screen PositionAdjusting OSD Menu Parameters OSD Position and Timer Adjusting Display Color Red, Green, BlueAdjusting the OSD Timer setting Adjusting the Picture SharpnessOptimizing Picture Performance in DOS Graphic/Text Automatic Contrast AdjustmentReturning Recall to Factory Default Settings Troubleshooting TroubleshootingDisplay Troubleshooting Use these messages to address panel issues Troubleshooting VTM-D15/A 15 MultiMedia Touch Panel Systems 12/02
Related manuals
Manual 52 pages 36.75 Kb

VTM-D15/A specifications

The AMX VTM-D15/A is a next-generation armored vehicle designed for versatility and adaptability in modern combat scenarios. Developed to meet the evolving demands of modern military operations, it embodies advanced technologies and exceptional characteristics that make it a standout choice for armed forces worldwide.

At the heart of the AMX VTM-D15/A is its robust chassis, designed to withstand harsh terrains and explosive devices. The vehicle boasts a well-protected hull using advanced composite materials and ballistic plating, ensuring crew safety in hostile environments. It can be fitted with reactive armor systems that enhance protection against projectiles and anti-tank missiles.

The VTM-D15/A features a powerful engine that provides high mobility across various landscapes, capable of reaching speeds of up to 100 km/h on flat terrain. Its off-road capabilities are complemented by a sophisticated suspension system that allows for excellent maneuverability in rugged conditions. The vehicle is also equipped with all-terrain tires, further enhancing stability and traction.

One of the remarkable aspects of the AMX VTM-D15/A is its modular design that allows for quick configuration changes between various combat roles. This adaptability permits the integration of different weapon systems, including machine guns and anti-tank guided missiles, that can be rapidly mounted or dismounted as per operational requirements.

The vehicle's advanced battlefield management system improves situational awareness, allowing for real-time data sharing and communication with other units. It is equipped with state-of-the-art sensors and reconnaissance tools, ensuring that it can gather intelligence and operate effectively in diverse combat environments.

Moreover, the AMX VTM-D15/A emphasizes crew comfort and ergonomics, featuring a spacious interior designed for extended missions. The vehicle's climate control systems and noise-reduction technologies significantly enhance crew endurance and focus in prolonged operations.

In a world where military operations are increasingly dynamic, the AMX VTM-D15/A stands out as a versatile, powerful, and technologically advanced armored vehicle. Its combination of protection, mobility, and adaptability ensures that it can meet a wide array of mission requirements, making it a vital asset in modern military arsenals.