Radio Reception
Seek Tuning
1. Press the BND / TS to select the desired AM or FM band.
FM I ➜ FM II ➜ FT ➜ AM (A) ➜ AT (FT & AT are Travel Store bands.)
2. Press the 
TUN/ TRK
to tune in stations. Tuning automati- cally stops at a broadcasting frequency.
“SEEK ” indicator will appear on the display window. When tuned in to FM stereo broadcasting stations, the
“
” stereo signal indicator will appear on the display window.
Preset Scan Tuning
1. | Press the | BND / TS to select the desired AM or FM band. |
2. | Hold the | SC/PS pressed for more than 2 seconds. |
“SCAN ” indicator will appear on the display window. The unit will scan preset memory for the 12 stations from the AM/AT band or the 18 stations from the FM I/FM II/ FT bands. The unit will stop at each preset station for 8 seconds, before continuing to the next preset station. Press the SC/PS again to stop Preset Scan Tuning and remain this on the selected frequency.
Receiving the Memorized Stations
1. | Press the | BND / TS to select the desired AM or FM band. |
2. | Press the | 1 ➜ 6 momentarily. |
Local/Distant (LO/DX) Selection
This feature is used to select the signal strength at which the radio will stop during Seek Tuning.
Press the 
for more than 2 seconds to select the Local setting and only strong (local) stations will be received. The “ lo ” indicator appears on the display window.
ENGLISH
Manual Tuning
1. | Press the | BND / TS | to select the desired AM or FM band. | ||
2. | Press the | TUN/ TRK | or | TUN/ TRK | for more than 0.5 sec- |
ond to activate the manual tuning mode. Press again to tune in to stations.
“MANUAL ” indicator will appear on the display window. After 4 seconds of completing Manual Tuning, the tuning control will revert to the Seek Tuning mode.
Scan Tuning
1. | Press the | BND / TS to select the desired AM or FM band. |
2. | Hold the | SC/PS pressed for less than 2 seconds. |
| The unit will scan the selected band for stations. | |
“SCAN ” indicator will appear on the display window. The unit will stop at each station for 8 seconds, before con- tinuing to the next station.
Press the SC/PS again to stop Scan Tuning and remain this on the selected frequency.
Tip
While tuning, the 
on the display is lit differently depending on the strength of the signal. While scanning bands, the
Memorizing Stations Automatically (Travel Store)
1. Press the 
to select the desired AM or FM band.
2. Hold the 
pressed for longer than 2 seconds. Up to 6 stations with strong signals will be automatically stored in preset memory for the selected band.
If the radio is in FM I or FM II, it switches to FT. If the radio is in AM, it switches to AT.
Note
This function is available for FT and AT.
Memorizing Only the Desired Stations
You can store up to 6 stations on each band (18 for FM I, FM
IIand FT, 12 for AM and AT) in the order of your choice.
1. | Press the | BND / TS to select the desired band. | |
2. | Press the | TUN/ TRK | to tune in stations. |
3. | Press and hold the desired preset memory button 1 - | ||
6for about 2 seconds until the frequency indicator flashes twice.
The number of the pressed preset memory button ap- pears on the display window.
Note
If when you store another station on the same preset number button, the previously stored station is replaced with new one.
Pressing for more than 2 seconds again will select the Dis- tant setting and the radio will stop at a wider range of signals, including weaker more distant stations. The “ lo ” indicator will go out on the display window. DX is the suggested default setting.