Kenwood TM-D700 E Digital Code Squelch DCS, Using DCS, Press Tone to activate the DCS function

Page 63

DIGITAL CODE SQUELCH (DCS)

Digital Code Squelch (DCS) is another application which allows you to ignore (not hear) unwanted calls. It functions the same way as CTCSS. The only differences are the encode/ decode method and the number of selectable codes. For DCS, you can select from 104 different codes listed in the table.

Received

DCS code: 125

Not Received

USING DCS

1Press the left or right [BAND SEL] to select band A or B.

•If necessary, press [F], then the same [BAND SEL] to recall the sub-band.

2Press [TONE] to activate the DCS function.

•“DCS” appears when the DCS function is ON.

•Each press of [TONE] changes the selection as Tone –> CTCSS –> DCS –> No selection.

3Press [F], [T.SEL].

•The current DCS code appears and blinks.

DCS code: 125

DCS code: 205

11

023	065	132	205	255	331	413	465	612	731

025	071	134	212	261	332	423	466	624	732

026	072	143	223	263	343	431	503	627	734

031	073	145	225	265	346	432	506	631	743

032	074	152	226	266	351	445	516	632	754

036	114	155	243	271	356	446	523	654

043	115	156	244	274	364	452	526	662

047	116	162	245	306	365	454	532	664

051	122	165	246	311	371	455	546	703

053	125	172	251	315	411	462	565	712

054	131	174	252	325	412	464	606	723

4Press [c]/ [d] to select a DCS code, then press [OK].

You will hear calls only when the selected code is received. To answer the call, press and hold Mic [PTT], then speak into the microphone.

Note: You cannot use the DCS with the Tone or CTCSS function.

57

Image 63

Contents TM-D700A Features Thank YOUModels Covered by this Manual One or more of the following statements may be applicable When condensation occurs inside the transceiverContents Locking Out a Memory Channel Selecting the Number of Channels Using Visual ScanSetting Scan Limits Using Program Scan Recalling the Call Channel Reprogramming the Call ChannelSquelch Hang Time Changing MULTI-FUNCTIONConventions Followed in this Manual Supplied AccessoriesMobile Installation Main Unit InstallationPreparation Slide the front panel down until its locking tab clicks Front Panel InstallationModular Plug Cable Connection Fixed Station InstallationMobile Operation DC Power Cable ConnectionPS-33 20.5 A, 25% duty cycle Fixed Station OperationFuse Location Fuse Current Rating Transceiver 15 a Supplied Accessory 20 a DC Power CableAntenna Connection Replacing FusesAccessory Connections External SpeakersMicrophone Ew wew w Your First QSOFront Panel Getting Acquainted3SQL control Main UNIT- Front Main UNIT- RearGPS jack Microphone Indicators Basic Transceiver Modes Button Function Display Control Band Band a & BTX Band and Control Band TX BandMIC Keypad Direct Entry MC-53DM only Operating Basics Switching Power ON/OFFAdjusting Volume Switch on the DC power supplySelecting a Frequency Adjusting SquelchSelecting Output Power When you finish speaking, release Mic PTTTransmitting Press c/ d to select the appropriate level 1 No Press OK Menu AccessPress MNU to enter Menu mode Menu SET-UPLevel Selections Default Menu ConfigurationMemory channel name See reference Number Store Auto PM Channel StoreChannel Display Memory Channel LockoutMic VFO Key See reference Visual Scan Automatic Power Off APORemote Control Mic PF Key See reference Mic MR KeyRSV report See reference Color for RSV report My call sign See reference Color for call signWhite Message See reference Color for messagePacket path See reference Commander call sign See reference Transporter call signSky Command mode Status text transmit rate See referenceOffset Programming Flow Operating Through RepeatersPress c / d to select Radio 1-, then press Programming OffsetSelecting Offset Direction Selecting Offset FrequencyPress F, T.SEL Activating Tone FunctionSelecting a Tone Frequency Press Tone to activate the Tone functionA. and Canada versions Automatic Repeater OffsetTransmitting a 1750 Hz Tone Press REV to switch the Reverse function on or OFF Reverse FunctionAutomatic Simplex Check ASC Press Scan to activate the Tone Freq. ID Tone FREQ. IDMemory Channels Simplex & Repeater or ODD-SPLIT Memory CHANNEL?Parameter Simplex Odd-split Storing ODD-SPLIT Repeater Frequencies Press M.IN 1 sSelect the desired transmit frequency Press M.IN Clearing a Memory Channel Select band a or B Press MR to enter Memory Recall modePress MHz Tuning control+ Power on Recalling a Memory ChannelRepeat steps 6 and 7 to enter up to 8 digits Turn the Tuning control to select the first digitNaming a Memory Channel Press aPress VFO Call ChannelRecalling the Call Channel Reprogramming the Call ChannelChannel Display MEMORY-TO-VFO Transfer440.000 MHz Partial or Full RESET?Parameter Band BProgrammable Information Programmable Memory PMSituationit ti Application ExamplesRecalling a PM Channel Storing in PM ChannelsPM Channel Reset Press PM+ Power onAuto PM Channel Store Scan Type Scan Range ScanSelecting the Number of Channels Mode 1 31 chMode 2 61 ch Visual ScanUsing Visual Scan Press F, Visual to start Visual ScanTo quit Visual Scan, press ESC Selecting Scan Resume Method Time-Operated modeCarrier-Operated mode Seek modeSelect band a or B VFO ScanMemory Scan Press VFO 1 sTo quit Group Scan, press MHz again Press MHz Tuning control 1 sGroup Scan Locking Out a Memory ChannelSetting Scan Limits Program ScanSelect the desired frequency as the lower limit Press F To quit MHz Scan, press MHz again Using Program ScanSelect the appropriate band To quit Program Scan, press VFO againTo quit Call/Memory Scan, press Call again CALL/VFO ScanCALL/MEMORY Scan To quit Call/VFO Scan, press Call againPress Tone to activate the Ctcss function Using CtcssContinuous Tone Coded Squelch System Ctcss Press the left or right Band SEL to select band a or BPress Scan to activate the Ctcss Freq. ID Ctcss FREQ. IDUsing DCS Digital Code Squelch DCSPress Tone to activate the DCS function Press Scan to activate the DCS Code ID DCS Code IDManual Dialing Dtmf MonitorFreq. Hz 1209 1336 1477 1633 Repeat steps 4 and 5 to enter up to 8 digits Turn the Tuning control to select a characterAutomatic Dialer Storing a Dtmf Number in MemoryTransmitting a Stored Dtmf Number Selecting TX SpeedSelecting Pause Duration VFO PF3 Programmable Function PF KeysPF PF1 MR PF2Auxiliary Functions Press VFO Press Mic EnterPress the numeric keys in sequence on the keypad Press c/ d to select the desired step size Changing Frequency Step SizeProgrammable VFO Press VFO Press F, StepAuto Dimmer Change Display Contrast Adjust Display DimmerPOSITIVE/ Negative Reversal Automatic Band Change A.B.C Blanking a Band DisplayChanging MULTI-FUNCTION Button Labels PWR switch MHz SQL controls VOL controlsPress F, MHz to switch the function on or OFF Transceiver LockSquelch Hang Time Meter SquelchAdvanced Intercept Point AIP Changing Beep VolumeSwitching FM/AM Mode KEY Beep ON/ OFFAutomatic Power OFF APO TIME-OUT Timer TOTPOWER-ON Message Display DemonstrationRepeat steps 3 and 4 to enter up to 8 digits Changing TX/RX Deviation TM-D700E only Changing Speaker ConfigurationsConnection Mode Band a Band B Speaker MuteMicrophone Control with MC-53DM only Preparation Wireless Remote Control U.S.A./ Canada onlyDigits Enter or VFO UP/ Down Access Menu 1-A-3 Control and select onControl Operation Select the receive frequency on band B UHFFreq SKY Command 2 U.S.A./ Canada onlyTM-D700A Connecting the Transporter with the HF Transceiver17 r Preparation FlowOn Transporter On CommanderProgramming Call Signs Programming a Tone FrequencyRIT ON/ OFF XIT ON/ OFF Mic Key FunctionT y Repeater Function U.S.A./ Canada only Band SEL VS-3 Voice Synthesizer OptionalMC-45 MC-53DM MC-80 MJ-88 MJ-89 Optional AccessoriesPS-33 SP-50B VS-3 VC-H1 PG-2N PG-3B PG-4X PG-5AReplace the lower cover 6 screws Installing OptionsInstalling the PG-4X Extension Cable KIT Remove the 6 screws from the lower cover of the main unitConnections Using Two Sets of PG-4X Kits Connections Using One Set of PG-4X KitCleaning MaintenanceService Service NoteProblem Probable Cause Corrective Action TroubleshootingCOM Port VHF Band UHF Band SpecificationsSub VHF or UHF band TransmitterIndex