Sharp DHS1050P operation manual E-12, QTimer playback, QSleep operation

Timer and sleep operation (Remote control only) (continued)

1 minute or more

Daily timer Once timer

Start Stop Start Stop

QTimer playback

Before setting timer:

1Check that the clock is set to the correct time. If it is not set, you cannot use the timer function.

2For timer playback: Plug in USB, dock iPod/iPhone, load discs or tape to be played.

1Press the ON/STAND-BY button to turn the power on.

2Press and hold the CLOCK/TIMER button.

3Within 10 seconds, press the or button to select “ONCE” or “DAILY”, and press the MEMORY button. Set the clock to the correct time if “ONCE” or “DAILY” does not appear.

4Within 10 seconds, press the or button to select “ONCE SET” or “DAILY SET”, and press the MEMORY button.

5To adjust the hour, press the or button and then press the MEMORY button.

6To adjust the minutes, press the or button and then press the MEMORY button.

7Set the time to finish as in steps 5 and 6 above.

8To select the timer playback source (CD, TUNER, USB,

iPhone/iPod, TAPE or AUDIO IN), press the or button. Press the MEMORY button.

When you select the tuner, select a station by pressing

the or button, and then press the MEMORY button. If a station has not been programmed, “NO PRESET” will be displayed and timer setting will be canceled.

10Adjust the volume using the VOLUME control, and then press the MEMORY button. Do not turn the volume up too high.

11Press the ON/STAND-BY button to enter the power stand-by mode. The “TIMER” indicator lights up and the unit is ready for timer playback.

TIMER

POWER

VOL.VOL.

iPod/iPhone

CD

TUNING PRESET

AUDIO IN

USB

12 When the preset time is reached, playback will start. The volume will increase gradually until it reaches the preset volume. The “” or “DAILY” indicator will blink

during timer playback.

13 When the timer end time is reached, the system will enter the power stand-by mode automatically.

Once timer:

The timer will be canceled.

Daily timer:

The timer operates at the same time every day. It will continue until the daily timer setting is canceled.

Cancel the daily timer when it is not in use.

Notes:

OWhen performing timer playback using another unit connected to the USB terminal or AUDIO IN jack, select “USB” or “AUDIO IN” in step 8.

OThis unit will turn on or enter the power stand-by mode automatically. However, the connected unit will not turn on or off. To stop the timer playback, follow step “Canceling the timer setting” of this page.

Checking the timer setting:

1Turn the power on and press and hold down the CLOCK/TIMER button.

2Within 10 seconds, press the or button to select “ONCE” or “DAILY”, and press the MEMORY button.

3Within 10 seconds, press the or button to select “ONCE CALL” or “DAILY CALL”, and press the MEMORY button.

Canceling the timer setting:

1Turn the power on and press and hold down the CLOCK/TIMER button.

2Within 10 seconds, press the or button to select “ONCE” or “DAILY”, and press the MEMORY button.

3Within 10 seconds, press the or button to select “ONCE OFF” or “DAILY OFF”, and press the MEMORY button. Timer will be canceled (the setting will not be canceled).

Reusing the memorized timer setting:

The timer setting will be memorized once it is entered. To reuse the same setting, perform the following operations.

1Turn the power on and press and hold down the CLOCK/TIMER button.

2Within 10 seconds, press the or button to select “ONCE” or “DAILY”, and press the MEMORY button.

3Within 10 seconds, press the or button to select “ONCE ON” or “DAILY ON”, and press the MEMORY button.

4Press the ON/STAND-BY button to enter the power stand-by mode.

QSleep operation

The iPod, Audio In, radio, CD, MP3/WMA disc, USB and cassette tape can all be turned off automatically.

1Play back the desired sound source.

2Press the SLEEP button.

3Within 10 seconds, press the SLEEP button repeatedly to select the time and then press the MEMORY button.

10 20 30 ....... 80 90

4“SLEEP” will appear.

5The unit will enter the power stand-by mode automatically after the preset time has elapsed. The volume will be turned down 1 minute before the sleep operation finishes.

To confirm the remaining sleep time:

1While “SLEEP” is indicated, press the SLEEP button.

To cancel the sleep operation:

Press the ON/STAND-BY button while “SLEEP” is indicated. To cancel the sleep operation without setting the unit to the stand-by mode, proceed as follows.

1While “SLEEP” is indicated, press the SLEEP button.

2Within 10 seconds, press the SLEEP button repeatedly to select “SLEEP OFF” and then press the MEMORY button.

E-12