Sharp DHS1050P Listening to the iPod or iPhone, QiPod and iPhone adaptor connection

Page 7
Listening to the iPod or iPhone

Listening to the iPod or iPhone

iPhone and iPod operations Made for:

O iPhone 4

O

iPod touch (1st generation)

O iPhone 3GS

O

iPod classic

O iPhone 3G

O

iPod nano (6th generation)

O iPhone

O

iPod nano (5th generation)

O iPod touch (4th generation)

O

iPod nano (4th generation)

O iPod touch (3rd generation)

O

iPod nano (3rd generation)

O iPod touch (2nd generation) O

iPod nano (2nd generation)

Caution:

Please update your iPod unit to the latest software version from Apple’s homepage before using it.

Notes:

OOnce the iPod or iPhone is connected to the unit it will begin charging.

OThe iPod or iPhone unit cannot be charged while the main unit is in the stand-by mode or during USB mode.

OThe message “This accessory is not made to work with iPhone” or similar, may appear on the iPhone screen when:

-battery is low.

-the iPhone is not properly docked (eg. slanting).

If this occurs, remove and re-dock the iPhone.

OThis product is made for iPhone. To prevent random interference when iPhone is docked, the headphone output is disabled, and “HP INVALID” will be displayed. You may also experience brief audio interference during incoming calls.

QiPod and iPhone adaptor connection

Notes:

OPlease use the adaptor supplied with your iPod or iPhone unit.

OYou can use an audio cable to connect your iPod to the AUDIO IN jack if:

1.your iPod adaptor does not fit into the iPod dock on the main unit.

2.you have an iPod that does not have an iPod adaptor.

3.you have an iPod that does not have an iPod 30 pin connector.

iPhone

iPhone

Capacity

Adaptor No.

Description

 

 

 

 

12

iPhone

4GB & 8GB & 16GB

 

 

 

15

iPhone 3G

8GB & 16GB

 

 

 

15

iPhone 3GS

16GB & 32GB

 

 

 

19

iPhone 4

16GB & 32GB

 

 

 

QTo remove iPod or iPhone adaptor

Insert the tip of a screwdriver (“-” type, small) into the adaptor hole as shown and lift upward to remove.

QiPod or iPhone playback

1Press the ON/STAND-BY button to turn the power on.

2Press the iPod/iPhone button to select iPod or iPhone function.

3Insert iPod or iPhone unit in iPod or iPhone dock of main unit. “DOCK OK” will be displayed.

4Press the QiPod and iPhone adaptor connectionQTo remove iPod or iPhone adaptor (iPod or iPhone QiPod or iPhone playbackQiPhone playback) button to start playback.

Note:

iPod and iPhone cannot be played back via USB cable and connection, “NO SUPPORT” will be displayed.

QiPhone playback

OSound will only switch from iPhone to the main unit after authentication process is completed in approximately 10 seconds.

OIncoming calls will pause the playback.

OOnce the calls are answered, the conversation can only be heard through the built-in iPhone speaker. Turn on the iPhone speaker or undock the iPhone to start conversation.

QTo disconnect iPod or iPhone

Simply remove the iPod or iPhone from the iPod or iPhone dock. It is safe to do so even during playback.

QNavigating the iPod or iPhone menus

1Press the MENU button to view the menu on iPod or iPhone unit. Press it again to go back to previous menu.

2Use the PRESET ( QTo disconnect iPod or iPhone or QNavigating the iPod or iPhone menus ) button to select an item on the menu and then press ENTER button.

Note:

When navigating the iPod or iPhone menu with remote control, do not operate any of the buttons on the iPod or iPhone unit. The volume level is adjusted by turning the volume knob on main unit or pressing the VOL (+ or –) button on the remote control. Adjusting the volume on the iPod unit gives no effect.

iPod or iPhone operation

Q To insert iPod or iPhone adaptor

 

The operations described below depend on the generation

Insert the iPod or iPhone adaptor into the unit and connect

iPod or iPhone you are using.

 

your iPod or iPhone.

 

 

System on operation

 

 

 

When the main unit is powered on, the iPod or iPhone

 

iPhone

 

unit will automatically power on when docked in the unit

 

 

(including TIMER function).

 

adaptor

 

 

iPhone

System off (stand-by operation)

 

 

iPhone

iPhone dock

connector

When the main unit is turned to stand-by mode, the

 

iPhone (bottom)

 

 

docked iPod or iPhone unit will automatically turn to stand-

 

 

by mode.

 

 

 

Dock connector

 

 

 

 

 

 

E-6

Image 7
Contents ENGLISH AccessoriesSpecial Note CD-DHS1050PSPECIAL NOTES IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS continued PrecautionsQGeneral For U.S. customer only CONSUMER LIMITED WARRANTYPrecautions continued QVolume controlQBattery installation Remote controlSystem connections continued QAuto power off function QAuto power on functionQTo turn the power on QVolume auto fade-inQiPod or iPhone playback Listening to the iPod or iPhoneQiPod and iPhone adaptor connection QTo remove iPod or iPhone adaptorQ Watching videos on a TV connected to Listening to a CD or MP3/WMA discQ Disc playback Q Various disc functionsQRepeat play Listening to a CD or MP3/WMA disc continuedQDirect track search QProgrammed playQTo play back USB/MP3 player with folder mode on Listening to USB mass storage device/MP3 playerAdvanced USB playback QTo play back USB/MP3 player with folder mode offListening to the radio QTuningQTo scan the preset stations QTo erase entire preset memoryListening to a cassette tape Setting the clock Remote control onlyTimer and sleep operation Remote control only QCleaning the tape-handlingpartsE-12 QTimer playbackQSleep operation Enhancing your system Troubleshooting chartQTo use timer and sleep operation together QHeadphonesQIf problem occurs MaintenanceTroubleshooting chart continued QRemote controlQ Tuner SpecificationsE-15 Q Amplifier