Alpine Installation and Connections for Car Stereo Systems
Page 42

Installation and Connections

Before installing or connecting the unit, please read the following and pages 3 to 5 of this manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury.

If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.

Precautions

•Be sure to disconnect the cable from the (–) battery post before installing your CDA-9815RB/CDA-9813R/CDA-9812RX/ CDA-9811R. This will reduce any chance of damage to the unit in case of a short-circuit.

•Be sure to connect the colour coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle's electrical system.

•When making connections to the vehicle's electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the CDA-9815RB/CDA-9813R/ CDA-9812RX/CDA-9811R to the fuse box, make sure the fuse for the intended circuit of the CDA-9815RB/CDA-9813R/ CDA-9812RX/CDA-9811R has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer.

•The CDA-9815RB/CDA-9813R/CDA-9812RX/CDA-9811R uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance.

•Be sure to connect the speaker (–) leads to the speaker (–) terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit.

SERIAL NUMBER:

INSTALLATION DATE:

INSTALLATION TECHNICIAN: PLACE OF PURCHASE:

40-EN

Page 41 Page 43
Image 42
Page 41 Page 43
Contents CDA-9815RB CDA-9813R CDA-9812RB CDA-9812RR CHM-S630 CHA-S634 CHA-1214Contents Installation and Connections Operating Instructions Never Attempt the Following On handling Compact Discs CD/CD-R/CD-RW Getting Started Press DISP/B.OUT to switch the display pattern Detaching and Attaching the Front PanelTuning to Preset Stations Manual Storing of Station PresetsAutomatic Memory of Station Presets RadioStation Title Search Function Setting RDS Reception Mode and Receiving RDS StationsPress Search in Radio mode to switch to Title Search mode Quick Search FunctionReceiving RDS Regional Local Stations Recalling Preset RDS StationsPI Seek Setting Receiving Traffic InformationPress T.INFO to deactivate the Traffic Information mode PTY Programme Type TuningWhen traffic information stations cannot be received Receiving Traffic Information While Playing CD or RadioDisplaying Radio Text Press 2/P.PTY to activate the Priority PTY mode againPriority PTY Programme Type 12-ENPlayback 13-ENX. Random Play Press 5 in the play or pause modeRepeat Play 14-ENScanning Programmes File Search modeFolder Search mode Quick SearchTerminology 16-ENPress Rotary encoder repeatedly to choose the desired mode Sound SettingSetting the Bass Control CDA-9812RX/CDA- 9811R only 17-ENEqualizer Presets CDA-9815RB/CDA-9813R only Setting the Treble Control CDA-9812RX/CDA- 9811R onlySetting the Bass Type CDA-9812RX/CDA- 9811R only 18-EN19-EN WAY System 20-ENExample 2. Listening Position All Seats About Time CorrectionExample 1. Listening Position Front Left Seat 21-ENBass Focus Example setting for steps 2Press T.CORR/X-OVER to select the Bass Focus mode 22-ENPress Rotary encoder to return to normal mode Setting the MX ModePress BAND/TEL. to select a speaker to be adjusted 23-ENDisplaying the Title/Text About the indicator displayOther Functions 24-ENErasing Disc Title/Station Title Blackout Mode On and OffTitling Discs/Stations 25-ENData Downloading PersonalizeAbout i-Personalize 26-ENSound Customizing Visual Customizing27-EN External Device 28-ENChanging the Service Component Using DAB Receiver for the Ensemble Seek Tuning OptionalChanging the Service DAB OptionalSelected service is received Memorizing the ServiceReceiving the Memorized Service Memorizing the Ensemble AutomaticallySetting the Announcement Select Mode Changing the Display Mode31-EN Displaying the Regional Label Setting for Automatic Change from DAB toSetting ON/OFF for DRC Dynamic Range Control Receiving Announcement Information of DAB Local StationsIncoming Calls Telephone Mode ON/OFFMobileHub Link OperationOptional About MobileHub LinkCalling SMS Short Message Service OperationCalling by using the Speed Dial Calling by the address bookPlaying MP3 Files with the CD Changer Optional Changer OptionalControlling CD Changer Optional Multi-Changer Selection OptionalRemote Control 36-EN Basic Information Case of Difficulty RadioIndication for CD Player Indication for CD Changer38-EN 39-EN SpecificationsRemote Control CDA-9815RB/CDA-9813R/CDA-9812RX only Bottom side of playerInstallation and Connections 40-ENInstallation 41-ENRemoval Connections for CDA-9812RX/CDA-9811R 42-EN43-EN To prevent noise/interference in the audio systemConnections for CDA-9815RB/CDA-9813R 44-ENAntenna Receptacle # System Switch 45-EN
Related manuals
Manual 48 pages 34.46 Kb
Top Page Image Contents