Operating Instructions
Playback (Basic play)
Refer to the illustrations on pages 28 to 29 of the Japanese text.
Preparation
≥Release HOLD.
≥Insert a MD.
1 Connect the remote control and earphones, then insert the remote control’s plug into the headphone jack [Ë] on the unit.
2Main unit
Press [1/;] to start play.
Remote control
Press [1/∫] to start play.
The unit stops automatically when all the tracks on the disc have been played.
3Adjust the volume.
r: To increase the volume level
s: To decrease the volume level Volume level is
To listen through the speakers
Refer to the illustration on page 30 of the Japanese text.
1.Insert a rechargeable battery into the unit.
2.Install the unit to the multi cradle.
3.Connect the AC adaptor to the multi cradle.
4.Connect the speakers to the multi cradle.
To operate the settings for the speakers use the same process as for stereo earphones.
Adjusting the volume
Can also be performed using the multi cradle [M s, r L, VOL/CURSOR ] buttons.
Note
≥Make sure you connect the AC adaptor as sound will not be produced by the speakers if you use only batteries.
≥You may listen to the music you are recording via the speakers (excepting when you are recording using a microphone).
Intro-scan memory
You can operate this function only using remote control.
Scan the introductions of tracks and program a maximum of 16 tracks in the order you want to hear them.
∫Program the tracks
1. While stopped, press [PLAY MODE] until “INTRO” appears.
The unit powers itself off in about 1 minute if you do not perform another operation.
2. Press [1/∫].
≥The first 10 seconds of each track are played in order
≥You can skip tracks during
3. Press [T.MARK/EQ] while the track number is flashing to program the track.
When the introduction of the last track is played,
Using the program play
If “MEMO” is on the display, start from step 2.
1.While stopped, press [PLAY MODE] until “MEMO” appears.
2.Press [1/∫].
≥The tracks are played in the programmed order.
≥During program play, “MEMO” is displayed after the track’s title on the remote control’s display.
∫To stop play
Press [1/∫].
∫To cancel program play (The program is stored)
Press [PLAY MODE] while stopped or playing. (“MEMO” disappears, the time information is shown, and normal play is restored.)
∫The program is cleared in the following cases
≥You Clear all tracks |
≥The battery goes flat |
∫To pause play
Main unit
Press [1/;] during play.
Playback starts when pressed again.
∫To stop the disc
Main unit
Press [∫/OPR OFF].
Remote control
Press [1/∫].
≥The unit powers itself off automatically in about a minute.
≥You can turn off the unit by pressing again [∫/OPR OFF] on the main unit while stopped.
∫Playback for long times ≥MDLP
≥You can play tracks recorded with MDLP mode.
≥Monaural playback
≥If a disc was recorded monaurally, the unit automatically switches to monaural playback mode.
| The unit selects the play mode according to |
| the recording mode: normal stereo, 2 x play |
| stereo (LP2), or 4 x play stereo (LP4), |
| monaural. |
RQT6558 | ∫Resume function |
again, play begins from that point. This does | |
| The unit stores the point at which play was |
stopped and if [1/ ;] on the main unit or [1/∫] on the remote control is pressed
not work if the unit is opened or if the battery
86is removed. The unit starts play from the first
track in these cases.
Other playback functions
Refer to the illustrations on pages 31 to 36 of the Japanese text.
Skip
This function skips tracks and play begins from the beginning of the selected track.
Main unitRemote control
Press [:, 9] during play.
Forward : [9] Backward : [:]
If you keep the button depressed the unit will continue to skip tracks
Search
This function allows you to
Main unit | Remote control |
Press and hold [:, 9] during play.
Forward : [9] Backward : [:]
Track select
This function allows you to begin listening from a selected track.
1 | Main unit | Remote control |
Press [:, 9] while stopped to select the track you like.
Forward : [9] Backward : [:]
If you keep the button depressed the unit will continue to skip tracks
2Main unit
Press [1/;] to start play.
Remote control
Press [1/∫] to start play.
Play starts from the selected track and plays through to the final track.
4. Repeat step 3 to program all the tracks you want.
5. Press [1/∫] to finish programming.
You can start play of the program by pressing [1/∫].
∫If “END” or “FULL” is displayed
You cannot program any more tracks.
END : you have programmed all tracks on the disc.
FULL : you have programmed the maximum of 16 tracks.
Programming ends 2 seconds after either of these is displayed.
∫To make a new program
Clear all tracks
While stopped and “MEMO” is on the display, press and hold [T.MARK/EQ] for about 5 seconds.
“CLEAR” is displayed and all tracks are cleared. “INTRO” appears on the display after this. Start from step 2.
∫To cancel intro scan
Press [PLAY MODE] while stopped. (“INTRO” disappears, the time information is shown, and normal play is restored.)
Note
It is not possible to use
≥You open the disc lid |
|
| |
≥You open the battery cover |
|
| |
≥You activate recording |
|
| |
≥You press [EDIT] and editing operations are | Instructions | ||
carried out. |
| ||
≥You activate Net MD. |
| ||
Sound quality |
| ||
Main unit |
| ||
Press [EQ/ REC SENS] when the unit is | |||
stopped or playing. |
| Operating | |
Remote control |
| ||
Press [T.MARK/EQ] when the unit is | |||
stopped or playing. |
| ||
The mode changes each time the button is | |||
| |||
pressed. |
|
| |
] |
| ||
Increases the power of |
| ||
| |||
the bass sounds. |
| ||
; |
| ||
| |||
Increases the |
| ||
; |
| ||
TRAIN |
| ||
Reduces sounds that may annoy |
| ||
others when you are using the |
| ||
unit in a public place. |
| ||
; |
| ||
NORMAL | } | RQT6558 | |
|
| ||
|
|
| |
|
| 87 | |
|
|
| |