Sony MDM-7A, NEW, KMS-2608/J1N specifications Traverse Adjustment, Iop NV Save

Page 27

7. Then, rotate the AMS knob and display “LDPWR CHECK”.

8. Press the YES button once and display “LD 0.9 mW $ ”. Check that the reading of the laser power meter become 0.85 to

0.91 mW.

9.Press the YES button once more and display “LD 7.0 mW $

”. Check that the reading the laser power meter and digital volt meter satisfy the specified value.

Note down the digital voltmeter reading value.

Specified Value :

Laser power meter reading : 7.0 ± 0.2 mW

Digital voltmeter reading : Optical pick-up displayed value ± 10%

(Optical pick-up label)

KMS260B

(For details of the method for checking

20101

this value, refer to “5-8. Recording and

Displaying IOP Information”.)

H0576

 

 

 

R

 

Iop = 57.6 mA in this case

Iop (mA) = Digital voltmeter reading (mV)/1 ()

10.Press the MENU/NO button and display “LDPWR CHECK” and stop the laser emission.

(The MENU/NO button is effective at all times to stop the laser emission.)

11.Rotate the AMS knob to display “Iop.Write”.

12.Press the YES button. When the display becomes Ref=@@@.@ (@ is an arbitrary number), press the YES button to display “Measu=@@@.@” (@ is an arbitrary number).

13.The numbers which can be changed will blink. Input the Iop value noted down at step 9.

To select the number : Rotate the AMS knob.

To select the digit : Press the AMS knob

14.When the YES button is pressed, “Complete!” will be displayed momentarily. The value will be recorded in the non-volatile memory and the display will become “Iop Write”.

Note 1: After step 4, each time the YES button is pressed, the display will be switched between “LD 0.7 mW $ ”, “LD

6.2mW $ ”, and “LD Wp $ ”. Nothing needs to be performed here.

5-11. Iop NV SAVE

Write the reference values in the nonvolatile memory to perform “Iop compare”. As this involves rewriting the reference values, do not perform this procedure except when adjusting the laser power during replacement of the OP and when replacing the IC102. Otherwise the OP check may deteriorate.

Note: Perform this function with the optical pick-up set at room temperature.

Procedure

1.Rotate the AMS knob to display “Iop NV Save” (C06).

2.Press the YES button and display “Iop [stop]”.

3.After the display changes to “Iop =xxsave?”, press the YES button.

4.After “Complete!” is displayed momentarily, the display changes to “Iop 7.0 mW”.

5.After the display changes to “Iop=yysave?”, press the YES button.

6.When “Complete!” is displayed, it means that Iop NV saving has been completed.

5-12. TRAVERSE ADJUSTMENT

Connection :

Oscilloscope

BD board

CN105 pin 4 (TE)

CN105 pin 6 (VC)

V : 0.5 V/div

H : 10 ms/div

Input : DC mode

Adjusting Procedure :

1.Connect an oscilloscope to CN105 pin 4 (TE) and CN105 pin 6 (VC) of the BD board.

2.Load a test disc (MDW-74/GA-1). (Refer to Note 1.)

3.Press the M button and move the optical pick-up outside the pit.

4.Rotate the AMS knob and display “EF MO ADJUST”.

5.Press the YES button and display “EFB = MO-R”.

(Laser power READ power/Focus servo ON/tracking servo OFF/ spindle (S) servo ON)

6.Rotate the AMS knob so that the waveform of the oscilloscope becomes the specified value.

(When the AMS knob is rotated, the of “EFB= ” changes and the waveform changes.) In this adjustment, waveform var- ies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible.

(Read power traverse adjustment)

(Traverse Waveform)

A

VC

B

Specification A = B

7.Press the YES button and save the result of adjustment to the non-volatile memory (“EFB = SAVE” will be displayed for a moment. Then “EFB = MO-W” will be displayed).

8.Rotate the AMS knob so that the waveform of the oscilloscope becomes the specified value.

(When the AMS knob is rotated, the of “EFB- MO-W” changes and the waveform changes.) In this adjustment, wave- form varies at intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible.

(Write power traverse adjustment)

(Traverse Waveform)

A

VC

B

Specification A = B

9.Press the YES button, and save the adjustment results in the non-volatile memory. (“EFB = SAVE” will be displayed for a moment.)

10.“EFB = MO-P”. will be displayed.

The optical pick-up moves to the pit area automatically and servo is imposed.

27

Image 27
Contents Specifications InputsOutputs General Where purchased Power requirementsSupplied accessories SELF-DIAGNOSIS FunctionItems of Error History Mode Items and Contents Exploded Views Table of ContentsDisassembly DiagramsLeakage Section Service NotesSafety CHECK-OUT Flexible Circuit Board RepairingIOP JIG for Checking BD Board WaveformRecord Precedure Checks Prior to Parts Replacement and Adjustments Forced ResetMain Board Component Side Bit Binary Retry Cause Display ModeBit When Binary Higher Bits Lower Bits Hexa DetailsHexadecimal Binary Section General Front Panel Section Section DisassemblyPT BOARD, VOL-SEL Board Main BoardBD Board Mechanism Deck Section MDM-7AExiting the Test Mode Section Test ModePrecautions for USE of Test Mode Setting the Test ModeDisplay Details Mark Group Selecting the Test ModeMENU/NO Operating the Continuous Playback ModeMID OUTFunctions of Other Buttons Test Mode DisplaysMode display Error rate displayInformation When Memory NG is DisplayedMeanings of Other Displays Automatic SELF-DIAGNOSIS FunctionSection Electrical Adjustments Parts Replacement and AdjustmentCheck before replacement YES Adjustment flowPrecautions for Checking Laser Diode Emission Precautions for USE of Optical PICK- UP KMS-260BPrecautions for Adjustments Checks Prior to Repairs Using the Continuously Recorded DiscTraverse Waveform Auto CheckOther Checks Traverse CheckSelf-Recording/playback Check Play Check MO Error Rate CheckCD Error Rate Check Focus Bias CheckInitial Setting of Adjustment Value Temperature Compensation Offset AdjutmentLaser Power Adjustment Iop NV Save Traverse AdjustmentYES Focus Bias AdjustmentMO Auto Gain Control Output Level Adjustment Error Rate CheckAuto Gain Control Output Level Adjustment CD Auto Gain Control Output Level AdjustmentAdjusting Points and Connecting Points Circuit Boards Location Section DiagramsFor schematic diagrams For printed wiring boardsMDS-JE440 Block Diagrams BD SectionSclk Cclk Control Generator OSC Main SectionBD Board Main BoardDisplay Board Semiconductor Printed Wiring Board BD SectionPIN PIN Function Printed Wiring Board Main Section Side a Printed Wiring Board Main Section Side B PIN MDS-JE440 Schematic Diagram Main /3 See page 47 for IC Block Diagrams Printed Wiring Board Power Section Printed Wiring Board Display Section Schematic Diagram Display Section See page 34 for Waveforms IC101 CXA2523AR BD Board IC Block DiagramsIC400 LA5643 Main Board Pin No Pin Name Function IC PIN FunctionsMNT3 Sloc MNT0 FOKMNT1 Shck MNT2 XbusyAvdd MvciAsyo AsyiFS4 TfdrFfdr FrdrIC1 M30805SGP System Control Main Board HLDA/ALE Chassis Section Section Exploded ViewsNot supplied FL771 202 220 201 213 215 216 205 218 207 Mechanism MDM-7A259 Description Remarks Ref. No Section Electrical Parts ListIC TC7WU04FUTE12R Display KEY-SW SWITCH, Keyboard MENU/NOCN1 MainDiode MA8047-TX Vibrator Main VOL-SELSony Corporation

KMS-2608/J1N, MDM-7A, NEW specifications

Sony has long been a leader in the realm of electronic innovation, and the introduction of the NEW MDM-7A and KMS-2608/J1N models further solidifies this position. These devices are a testament to Sony's commitment to delivering cutting-edge technology that enhances user experience across various applications.

The MDM-7A, a multi-channel digital mixer, offers advanced audio processing capabilities, ideal for both studio and live sound environments. One of its standout features is its high-resolution 24-bit audio processing, which ensures crystal-clear sound reproduction and fidelity. The MDM-7A supports a wide range of audio formats, making it compatible with various production environments. Moreover, its intuitive user interface facilitates easy navigation and control over numerous audio channels while maintaining flexibility for complex setups.

On the other hand, the KMS-2608/J1N is a multichannel audio management system designed for more extensive sound setups. One of its primary features is the smart signal routing capability, which allows users to manage audio signals efficiently across different outputs. This is especially beneficial in large-scale events or installations where sound management can become challenging. With support for both analog and digital audio inputs, the KMS-2608/J1N caters to a variety of equipment, ensuring seamless integration with existing systems.

In terms of connectivity, both devices are equipped with multiple input and output options, including XLR and TRS connectors, along with digital interfaces such as AES/EBU and S/PDIF. This flexibility allows users to customize their audio setups according to specific needs and preferences.

Another defining characteristic of the MDM-7A and KMS-2608/J1N is their durability and reliability. Built with robust materials and designed for extensive use, these devices are engineered to withstand the rigors of professional use, making them a smart investment for audio professionals.

In conclusion, the Sony MDM-7A and KMS-2608/J1N embody the future of audio technology, combining superior sound performance with user-friendly features. These models are not only designed to meet current industry standards but are also forward-thinking, making them suitable for a wide array of applications, from studio recordings to live events. As Sony continues to innovate, these devices are sure to play a significant role in shaping the audio landscape for years to come.