Sony MZ-NF810 service manual Flexible Circuit Board Repairing, On power sources

Page 3

MZ-NF810/NF810CK

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous ra- diation exposure.

On power sources

•Use house current, nickel metal hydride rechargeable battery, LR6 (size AA) battery, or car battery.

•For use in your house: For the supplied battery charging stand, use the AC power adaptor supplied with this recorder. Do not use any other AC power adaptor since it may cause the recorder to malfunction.

Polarity of the plug

•Connect the AC power adaptor to an easily accessible AC outlet. Should you notice an abnormality in the AC power adaptor, disconnect it from the AC outlet immediately.

•The recorder is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the recorder itself has been turned off.

•If you are not going to use this recorder for a long time, be sure to disconnect the power supply (AC power adaptor, dry battery, rechargeable battery, or car battery cord). To remove the AC power adaptor from the wall outlet, grasp the adaptor plug itself; never pull the cord.

Notes on chip component replacement

•Never reuse a disconnected chip component.

•Notice that the minus side of a tantalum capacitor may be dam- aged by heat.

Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270 ˚C dur- ing repairing.

•Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

•Be careful not to apply force on the conductor when soldering or unsoldering.

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

•Unleaded solder melts at a temperature about 40 ˚C higher than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to about 350 ˚C .

Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

•Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

•Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

 

TABLE OF CONTENTS

 

1.

SERVICING NOTES

4

2.

GENERAL

5

3.DISASSEMBLY

3-1.

Disassembly Flow

6

3-2.

Case (Lower)

7

3-3.

MAIN Board, Battery Case

7

3-4.

Panel (Upper) Section

8

3-5.

LCD Module, Panel Upper Block

8

3-6.

Mechanism Deck (MT-MZN710-177)

9

3-7.

OP Service Assy (LCX-5R)

10

3-8.

Holder Assy

11

3-9.

DC Motor (Sled) (M602)

11

3-10.

DC Motor (Over Write Head Up/Down) (M603),

 

 

DC SSM18B Motor (Spindle) (M601)

12

4.

TEST MODE

13

5.

ELECTRICAL ADJUSTMENTS

18

6.DIAGRAMS

6-1.

Block Diagram

37

6-2. Note for Printed Wiring Board and

 

 

Schematic Diagrams

38

6-3. Printed Wiring Board

 

 

– MAIN Board (Side A) –

39

6-4. Printed Wiring Board

 

 

– MAIN Board (Side B) –

40

6-5.

Schematic Diagram – MAIN Board (1/4) –

41

6-6.

Schematic Diagram – MAIN Board (2/4) –

42

6-7.

Schematic Diagram – MAIN Board (3/4) –

43

6-8.

Schematic Diagram – MAIN Board (4/4) –

44

6-9.

IC Pin Function Description

50

7.EXPLODED VIEWS

7-1.

Case Section

56

7-2.

Chassis Section

57

7-3.

MAIN Board Section

58

7-4. Mechanism Deck Section-1 (MT-MZN710-177)

59

7-5. Mechanism Deck Section-2 (MT-MZN710-177)

60

8.

ELECTRICAL PARTS LIST

61

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE

PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUM- BERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE- MENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents MZ-NF810/NF810CK LR6 Battery lifeOn power sources Flexible Circuit Board RepairingSystem requirements Section Servicing NotesMZ-NF810/NF810CK Looking at controls Section GeneralDisassembly Flow Section DisassemblyCase Lower Main Board, Battery CaseLCD Module, Panel Upper Block Panel Upper SectionMechanism Deck MT-MZN710-177 Gear SA Screw M1.4 OP Service Assy LCX-5RDC Motor Sled M602 Holder AssyGear HA Releasing the Test Mode Section Test ModeOperation in Setting the Test Mode Setting Method of Test ModeA n u a l Configuration of Test ModeManual Mode Transition method in manual mode 1. Set the test mode see011 0 5 9 a 0 011 C 6 8 S 0F F J 0 011 0 6 3 B 0Description of indication history Reset the Error Display CodeDescription of error indication codes Setting method of reset the error display codeRP PUS 000 P * * R000 000 FFSetTmp ResOK?E s E s e t744 VC2 Hi 741 VC1 L742 VC1 H 743 VC2 LoVrec M 748 REG3L2749 REG3 H Vrec L758 CIH ChgV L757 CIL ChgV HAdjustment/checking and Connection Location ADJ OK Power Supply Adjustment Auto Item FeedConfiguration of power supply adjustment auto item feed AssyWrPwLo LaserLrefpw HrefPwMO OK Assy11000 *** NG CD OKMO overall adjustment items ResClr Resume Clear Setting Method043Resume 043 ResRewriting the Patch Data Rewriting the Patch Data at Replacement of Main Board IC851Preparation Pre-checkMZ-NF810/NF810CK MZ-NF810/NF810CK MZ-NF810/NF810CK How to get the application NVWriter for NV values rewriting Rewriting the NV valuesRewriting the NV values MZ-NF810/NF810CK MZ-NF810/NF810CK MZ-NF810/NF810CK Memo Block Diagram Section DiagramsLead Layouts WaveformsSemiconductor Location Printed Wiring Board Main Board Side a Uses unleaded solderMain Board Printed Wiring Board Main Board Side B Uses unleaded solderSSM1NI2P HP OUT R822 R824 47k 220k 470k Schematic Diagram Main Board 4/4 IC301 AK5356VN-N IC Block DiagramsIC501 SN761058ZQLR IC601 XPC18A22AEPR2 IC701 SC111258EPR2 IC901 SC901580EPR2 IC Pin Function Description Sens KrckXbck ExcsChgisel GndswFfclr ChgadselSO3 UosciUosco SI3DVSS2 XCSDVSS0 DVSS1Msak FVSS0Case Section Section Exploded ViewsChassis Section Except US,3CED,4CED,UK 302 308 306 303307 304 305309 310 Mechanism Deck MT-MZN710-177 301359 361 360 364 Mechanism Deck MT-MZN710-177 357 365 356 355354 353 352 351 358AUS Section Main Electrical Parts List¥ Resistors ¥ SemiconductorsCAP-CHIP XC61FS1YXXMR Resistor Metal CONNECTOR, Light US,CND,3CED,4CED,UK,TW,AUS,JE Memo Revision History

MZ-NF810 specifications

The Sony MZ-NF810 is a notable entry in the portable digital music player market, primarily aimed at users who seek high-quality audio playback and advanced recording capabilities. This MiniDisc player is celebrated for its compact design, making it an ideal companion for on-the-go listeners who value both audio quality and portability.

One of the standout features of the MZ-NF810 is its support for ATRAC compression technology. ATRAC, short for Adaptive Transform Acoustic Coding, provides a means to compress audio files while still maintaining impressive sound fidelity. This technology was specifically designed to optimize audio for the MiniDisc format, allowing users to enjoy longer playtimes without sacrificing sound quality. The MZ-NF810 can store up to 40 hours of music on a single battery charge, a significant advantage for audiophiles and casual listeners alike.

The device also boasts a high-resolution LCD display, providing crucial information about the currently playing track, including title, artist, and remaining battery life. Navigation is smooth and user-friendly, allowing users to access their music collections with ease. In addition, the MZ-NF810 supports USB connectivity, enabling users to transfer music and files directly from their computers. This feature eliminates the need for additional software, streamlining the process of loading music onto the device.

An important aspect of the MZ-NF810 is its recording capabilities. The player allows users to record live audio directly onto MiniDiscs, providing the freedom to capture concerts, lectures, or personal notes. The addition of various recording modes, including long-play options, enhances its utility for users who need diverse functionality.

Sound quality is further augmented with features such as Dynamic Bass Boost and a five-band equalizer, allowing users to tailor their listening experience to their preferences. The MZ-NF810 also supports various audio formats, adding to its versatility as a personal audio device.

Lastly, the MZ-NF810's sleek and lightweight design makes it not only aesthetically pleasing but also comfortable to carry, making it a practical choice for those who lead active lifestyles. In summary, the Sony MZ-NF810 MiniDisc player stands out for its audio quality, recording features, and user-friendly design, catering to music enthusiasts who demand both performance and portability in their listening experience.
Top Page Image Contents