Audio-Technica AT-LP60 manual Troubleshooting

Page 7

English

Troubleshooting

Turntable does not operate

1.Make certain the turntable’s AC cord is plugged into an AC outlet, and that the AC outlet is “live.”

2.Check the drive belt to make certain it is on correctly. (See Figure 11.)

A)Remove the record mat from the turntable platter (Fig. 11a). Place the mat in the cardboard packaging sleeve for safekeeping. Through an opening in the turntable platter, visually inspect to see if the drive belt is around the motor pulley (Fig. 11b).

B)If the drive belt is not around the motor pulley: Lift and remove the turntable. Place a thumb into each of the left and right openings on the turntable platter; and, using the fingers to press down on the turntable housing’s surface, pull the platter straight up (Fig. 11c). Avoid pressing on the tone arm.

C)With the turntable platter bottom side up, place the belt along the outside wall of the turntable platter’s drive rim, making certain that the belt is smooth and flat all the way around (Fig. 11d).

D)Put the turntable back on the center spindle, make certain it is fully seated, and align one of its openings over the motor pulley position.

E)Through the opening, carefully hook the turntable belt with a finger or with the original red ribbon (never use a sharp object) and pull the belt over the motor pulley (Fig. 11e). Make certain the belt is not twisted between the pulley and the platter’s drive rim.

F)Put the record mat back on the platter.

G)While holding the tone arm in its rest position, slowly turn the platter by hand clockwise at least 10 rotations to clear the mechanism’s automatic cycle.

Turntable operates, but no sound at all

1.The stylus guard is still in place.

2.The tone arm Lift button is pressed in.

3.Amplifier controls set incorrectly: wrong input selected, tape monitor on, speakers switched off, etc.

4.Check the stylus on phono cartridge for correct placement. Refer to the instructions for replacing the stylus on page 6.

Turntable operates, but no sound, or sound not loud enough

1.If the turntable is connected to an AUX (high-level) input: The Pre-amp Selector Switch may be set to the “PHONO” position (phono-input level).

2.The input gain of the amplified speaker or similar device may be too low.

3.The stylus assembly may not be fully seated in the cartridge body. (See Fig. 10 on page 6.)

Sound is very distorted

1.Turntable connected to an amplifier’s PHONO input: If the pre-amp switch is set to the “LINE” position (AUX high-level output), a phono input will be overloaded.

Record/Tone Arm moves slightly up and down

1.Usually this is a normal condition and not a problem. If this causes the turntable to be unable to track the record, please contact your dealer or our service department. Make very certain the surface upon which the turntable is resting is not picking up vibrations from the floor or walls, or from direct speaker sound.

Figure 11 – Checking the drive belt

11a

11b

11c

11d

Drive belt

11e

Motor pulley

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents AT-LP60 Automatic Stereo Turntable System Automatic Stereo Turntable System Safety instructionsIntroduction Front Main Features2a Drive belt Initial SetupSetting the Pre-amp Phono/Line Switch Assembling the TurntableAutomatic Operation Connecting to Stereo SystemConnecting to Computers or Audio Devices with 3.5 mm Input Operation10b Replacing the StylusManual Operation OutTroubleshooting Tips For Better Performance SpecificationsTips For Better Performance Instructions de sécurité Système de tourne-disque stéréo automatiqueAvant Principaux élémentsAssemblage du tourne-disque Configuration initialeRéglage du sélecteur de préamplification phono/ligne Utilisation Configuration initiale suiteConnexion au système stéréo Utilisation en mode manuel Remplacement de la pointeUtilisation suite Distorsion importante du son DépannageLe tourne-disque ne fonctionne pas Le tourne-disque fonctionne mais il n’y a pas de sonCaractéristiques techniques Conseils d’optimisation des performancesConseils d’optimisation des performances Instrucciones de seguridad Sistema tocadiscos estéreo automáticoIntroducción Figura Parte delantera Funciones principales2b Estera 2c Desinstalación de la cubierta antipolvo Instalación inicialMontaje del tocadiscos Ajuste del conmutador Phono/Line de preamplificadorFuncionamiento automático Instalación inicial continuaciónFuncionamiento Conexión al sistema estéreoSustitución de la aguja Funcionamiento continuaciónFuncionamiento manual El sonido está muy distorsionado Solución de problemasEl tocadiscos no funciona El tocadiscos funciona, pero no suenaEspecificaciones Consejos para un mejor rendimientoConsejos para un mejor rendimiento Español Garantie limitée de 1 an One-Year Limited WarrantyGarantía limitada de un año

AT-LP60 specifications

The Audio-Technica AT-LP60 is an acclaimed automatic belt-drive turntable designed to deliver high-quality audio performance while making vinyl playback accessible to all users. Whether you're a seasoned audiophile or a casual listener, the AT-LP60 offers a blend of user-friendly features and sophisticated technology.

One of the standout characteristics of the AT-LP60 is its fully automatic operation. With the simple push of a button, the tonearm engages and automatically lowers onto your vinyl record, enabling a seamless listening experience. This convenience makes it particularly appealing to those new to vinyl, as it simplifies the process compared to manual turntables.

The turntable features a precision-engineered belt-drive system, which plays records at both 33 1/3 and 45 RPM speeds. The belt-drive configuration helps reduce vibrations, ensuring that your records sound crisp and clear. The AT-LP60 is equipped with an integrated Dual Magnet cartridge and a replaceable stylus, which provides excellent sound reproduction while allowing users to easily upgrade or replace the stylus when necessary.

Incorporating cutting-edge technology, the AT-LP60 also comes with a built-in phono pre-amplifier. This allows users to connect the turntable directly to powered speakers or a standard audio system that lacks a dedicated phono input, offering versatility and ease of use. By eliminating the need for an external pre-amp, Audio-Technica ensures that any listener can enjoy high-fidelity sound without complicated setups.

The construction of the AT-LP60 includes a robust plinth designed to minimize resonance and external noise interference. This attention to build quality not only enhances the aesthetics of the unit but also contributes to its overall performance, giving users a reliable platform for their vinyl collections.

Moreover, the AT-LP60 comes with a detachable hinged dust cover, which protects the turntable and records from dust and debris. This thoughtful inclusion highlights Audio-Technica’s commitment to durability and maintenance ease.

In summary, the Audio-Technica AT-LP60 turntable combines style, user-friendliness, and excellent sound quality, making it a perfect entry point for anyone looking to dive into the world of vinyl records. With its automatic operation, built-in preamp, and versatile speed capabilities, it’s a fantastic choice for both casual listeners and more serious collectors.
Top Page Image Contents