Sierra Wireless 20070914 manual Serial, D.d=IP address

Page 106

Configuration Commands

*NETROAMPREF=n

Allow configuration of the roaming preference.

•n=0 : Restrict to home network only.

•n=1‐3 : Allow roaming to affiliated networks.

n=3

*NETUID=uid

The login that is used to login to the cellular network, when required.

•uid=user id (up to 64 bytes)

*STATICIP=d.d.d.d

Set the static IP required to be received from the network. If the modem does not get this IP address from the network, it will reset the internal hardware and try again. The default is 0.0.0.0, which allows any IP address from the network.

•d.d.d.d=IP address

Example:

AT*STATICIP=192.168.1.23

Caution: STATICIP does not set the IP address of the modem, it merely tells the modem which IP address to expect. If the expected IP address is not granted while registering on the cellular network, the modem will try to register on the network again until it receives that IP address. If your account is set up for a dynamic IP address and you set an address for *STATICIP, you may not be able to register on the network at all since there is no guarantee you will receive the same dynamic IP address again.

*STATUSCHK=n

Checks if an SMS message has been received by the modem.

•n=1‐255 : Seconds between checks.

•n=0 : Never check.

Serial

This group includes commands specific to general use of the serial port.

 

 

 

 

 

 

 

Rev 3.0B Feb.08

 

 

 

 

 

101

 

 

 

Page 105 Page 107
Image 106
Page 105 Page 107
Contents User Guide Important Notice Safety and Hazards Limitation Liability Patents Copyright Trademarks Qualcomm 3GSupport@sierrawireless.com Contact InformationRevision History Revision Release Changes Number DateContents Configuring your Raven Configuring Modbus/BSAP Contents Contents Contents Circuit Switch Communications Introduction to the Raven AleosAceWare AceManagerSimplified Deployment Monitor and ControlAceView AceNetNetwork Monitoring Setup Wizard Modem DoctorModem Doctor USB Modem DoctorConnecting to the Telus Network Steps of a connectionConnecting to the Internet Dynamic vs. Static IP Addresses1x Communication SecuritySpecifications Power Connector Interface Port Pin-OutsStarting the Setup Wizard Setup WizardActivating your Raven on the 3 Telus Network Connecting to the Modem Setup WizardSetup Wizard Connected Selecting TasksOptionalUpdate Aleos Aleos UpdateSetup Wizard Activation Code Activate ModemSetup Wizard MDN and MIN/MSID Test Modem Setup Setup Wizard Signal TestOptional Setting up a DUN Connection 10 Setup Wizard DUN driver12 Setup Wizard DUN connections Activating Using AT Commands 14 Setup Wizard DUNAT*PROVISION2=MSL,MDN,MIN/MSID,SID,NID Raven 20070914 Hardware Installation Raven MountingConnecting to Power Connecting to a Computer or other Device Indicator LightsMounting Light PatternsOptional Mounting Bracket Hardware Installation of the Raven Rev 3.0B Feb.08 Hardware Installation of the Raven Rev 3.0B Feb.08 Using AceManager Configuring your RavenStart AceManager Connect to your Raven AceManager Connect to ModemEnter the configuration options AceManager ConnectedWrite the changes to the modem Using TemplatesCreating the Template with AceManager · Cellular Technology specific settings the CDMA/EV‐DO group Reset the modem Applying a Template to one modem with AceManagerConfiguring your Raven 10 AceNet Selected modems Using a Terminal Application with AT Commands Choose a name and icon for your connectionPort Settings serial only Connect ToConnected · Flow Control HardwareAT Commands Basic Modes Data Communication and Host 6 ModesSerial Modes Basic Modes Start up ModeData Communication AT Mode PassThru Mode AceManager PassThruTelnet Mode Serial ModesAT\APPP UDP and UDP Pad UDP Auto AnswerReliable UDP UDP Multicast Mode TCP and TCP PadHybrid Modes TCP Auto AnswerUdplast Public and Private Mode Data CommunicationKeepalive Configuring Keepalive Data usage using KeepaliveIpping IP Manager Reasons to contact the modem and/or the connected deviceUnderstanding Domain Names Car54.mydomain.com Dynamic NamesCar54.mydomain.com.ca Using IP Manager with your Raven AceManager Dynamic IPEairlink.com Data Usage for IP Manager Server UpdatesRestrictions for Modem Name Configuring DNS Understanding DNSPPP-Peer Domain Name AceManager DNSTelemetry Configuring Modbus/BSAPModbus Overview Remote Terminal Unit RTUModbus TCP/IP Supervisory Control and Data Acquisition ScadaProgrammable Logic Controller PLC Raven Modbus on UDPConfiguring the Raven at Polling Host for Modbus on Configure the listening/device portsConfigure the default mode for start-up Configure IP addresses for the Modbus IDsOptional Dynamic IP Address Configuring the Remote Ravens for Modbus with UDP Configure the portsConfigure IP addresses for the host AceManager UDPConfigure other RTU settings AceManager DNS Raven 20070914 Management Information Base MIB Snmp Simple Network Management ProtocolSnmp Traps Listening Port Snmp ConfigurationSecurity Level User Name and Password AceManager Change Password menu optionTrap Destination Snmp MIB Definition SampleCommunity String Snmp Simple Network Management Protocol Snmp Simple Network Management Protocol Snmp Simple Network Management Protocol Display Responses Product ID Configuration Commands Info informationDEVICEID? NETPHONE?NETCHAN? StatusHOSTMODE? NETERR?Any other value Failure AT Commands Requiring PassThru mode +WHWV +ECIO?+GSN +WPRL?Misc Miscellaneous Common+++ Dmethodd.d.d.d/ppppp or Dmethod@name/ ppppp DS=nS53=methodd.d.d.d/ppppp OPRG=nMethod= P UDP Method=T TCP Method=N Telnet =1‐65535 Serial D.d=IP addressS4=n S3=nS5=n =1‐2545 =2‐10 seconds=0‐255 Parity=O Odd Parity=E Even Parity=N None Parity=M MarkS51=n S50=n=tenths of a second S211=n+IPR=n \APPP\Qn $QCVAD=nNUMTOIP=n CTSE=nModemhispeed PPPNOCARRIER=n=seconds S0=nS7=n S60=n=0 ‐ =intervalHh=01 Slip Hh=02 PPP Hh=03 UDP Hh=04 TCP HOR=nMDhh Hh=33 BsapUALL=n S83=nDU=n UDPLAST=nD.d=IP address of domain server DNSUPDATE=nDynamic IP DNSUSER=d.d.d.dName=domain name DOMAIN=nameIPMGRKEYn=key PPP/Ethernet IPMGRUPDATEn=mMODEMNAME=name HOSTAUTH=n DHCPSERVER=nHOSTNETMASK=n.n.n.n PassThru String=passwordD.d=local or peer IP address of the modem CSX1=n String=AT commands\APASSTHRU PTINIT=string=1‐255 minutes RESETPERIOD=nPTREFRESH=n =1‐255 hoursEmail=email address Body=message body Pw= password=SMS/E‐mail server number SMTPSTATUS?Subject=message subject Dasms CntsmsIndex= index list 0, 1 Message= message number DAE=n OtherSSMS? DATZ=nD.d=IP address Name=domain name Resetcfg=15‐255 minutes Name=domain name Port=portHost=IP address Port=TCP port =1 On=minutes TELNETTIMEOUT=nFriends TPORT=nFM=n LoggingD.d = IP address DBGIPLVL=n Telemetry/Addr ListDBGCOMMLVL=n DBGPPPLVL=nMVMSK=hh IPL=nMVLEN=n Hh=hex valueMVTYP=n Addr ListMVOPT=n RKEY=nHexid=ID D.d=IP address or name 1x/EV-DOId=ID D.d=IP address or name +CTA=nPROVISION=MSL,MDN/MIN,SID,NID ~NAMLCK=nnnnnnNnnnnn=6 digit unlock code PROVISION2=MSL,MDN,MIN,SID,NID+WMDN=num +WIMI=numSid=system ID Nid=network ID Nam=0 Min=phone number Msid=second numberCircuit Switch Communications B Configuring Circuit-SwitchAT Commands and the Command String Commands Specific to the Raven 1x C3210 and C3216 Commands Specific to the Raven 1x C3211Raven LEDs in Circuit-Switched Mode Step by Step ConfigurationCommon AT Commands Hardware Required Software RequiredErase the internal memory Connect the modem to your computerInformation Required for CDMA/1x only Rev 3.0B Feb.08 139 Activate the Raven Start All Programs AirLink Communications AceManager 3GConfigure serial port speed Save the serial settingConfigure the Raven using a AceManager template 12 AceManager DisconnectConfigure additional PassThru settings 15 AceManager LoadReset the Raven Save the configuration settingsConfigure the Raven for your equipment Test the Raven ConfigurationCommission the Raven Modem on Site 146 20070914 Windows Dial-up Networking C DUN Installing a modem driver for RavenInstall the driver Connect the RavenSelect the Modems tab Check Don’t detect my modem I will select it from a list Check Selected Ports Configure the driver Modem PropertiesCreating a Dial-Up Networking PPP Connection Modem Properties ModemCreate a new network connection 10 Windows Start menuSelect Connect to the Internet Select Set up my connection manually Rev 3.0B Feb.08 156 Rev 3.0B Feb.08 157 Configure the DUN connection 21 New Connection FinishCheck Show icon...when connected Rev 3.0B Feb.08 160 Select Advanced Connecting to the Internet Using DUN Start AceViewEnable the Connection Windows DUNStart the DUN session Select Dial to connect to the modem and the cellular networkWindows Dial-up Networking DUN Rev 3.0B Feb.08 165
Related manuals
Manual 176 pages 17.38 Kb Manual 36 pages 19.88 Kb Manual 203 pages 17.49 Kb

20070914 specifications

Sierra Wireless 20070914 is a cutting-edge wireless communication module designed for IoT applications, offering remarkable features and robust performance. This module represents a significant advancement in the realm of embedded wireless solutions, catering to a variety of industries including automotive, industrial automation, and smart cities.

One of the key features of the Sierra Wireless 20070914 is its support for multiple cellular standards, including LTE, which ensures high-speed data transfer and reliable connectivity. The module is designed to operate on various frequency bands, making it versatile and suitable for global deployment. This multi-band capability allows businesses to deploy their IoT solutions in different regions without modification, reducing time-to-market and deployment costs.

Another standout characteristic of the Sierra Wireless 20070914 is its comprehensive and seamless integration with cloud services. The module supports advanced cloud connectivity options, enabling real-time data processing and analysis, which is crucial for industries that rely on timely decision-making. This feature is particularly important in sectors like transportation and logistics, where real-time tracking and monitoring are essential.

The power efficiency of the Sierra Wireless 20070914 is noteworthy. It is engineered to operate optimally in low-power modes, making it ideal for battery-operated devices. This focus on energy efficiency ensures prolonged device lifecycles, supporting the growing demand for sustainable and eco-friendly technologies.

Moreover, the module includes encrypted communication features, enhancing security and protecting sensitive data transmissions. With the increasing prevalence of cyber threats, this security aspect is critical for businesses looking to safeguard their IoT applications from unauthorized access and data breaches.

In addition to these features, the Sierra Wireless 20070914 offers comprehensive development support, including software development kits (SDKs) and application programming interfaces (APIs). This makes it easier for developers to integrate the module into their existing systems, streamlining the development process and accelerating innovation.

Overall, the Sierra Wireless 20070914 stands out as a powerful solution for IoT connectivity, blending advanced technology, security, and efficiency. Its capabilities are designed to support the diverse needs of modern industries, paving the way for future innovations and advancements in wireless communication. As businesses increasingly turn to IoT for modernization, modules like the Sierra Wireless 20070914 will play a crucial role in enabling this transformation.
Top Page Image Contents