Sierra Wireless 20070914 manual AT Commands

Page 54

Configuring your Raven

a.Type AT and press Enter. You should get a reply of “OK” or “0”.

b.To see what you are typing as you type it, you will need to turn on the echo and verbose mode. Type ATE1V1 and press Enter.

c.If you get a reply of “OK”, then you entered the command successfully. If you get a reply of “0” or “ERROR”, try entering the command again.

AT Commands

When using a terminal application, you will need to manually type in each command.

•For most commands, when you are entering them using a terminal connection, you will need to preface the command with AT (exceptions are noted), i.e. ATA which is listed as A.

•Some commands have specific parameters while other commands will take whatever you type.

•Required variable parameters are denoted with italicized text, example, Dn. The n is variable.

•Acceptable parameters and/or specific formats are listed with each command.

•Most commands with parameters can be entered with ? to read the current value (for example, AT&D? will respond with “2” if the default has not been changed).

•Optional parameters are denoted with square brackets [ ].

•AT Commands are not case sensitive. A capital “E” is the same as a lower‐case “e”.

•When you are using a terminal connection, if you enter a command which is recognized by the Raven, it will respond with “OK”. If the command is not recognized, the response will be “ERROR”.

•Those commands applicable only to certain model numbers of the Raven will be noted.

Caution: Symbols listed with commands, such as *, /, &, or ?, are part of the command and must be included. Commands with symbols other than * may require PassThru mode.

 

 

 

 

 

 

 

Rev 3.0B Feb.08

 

 

 

 

 

49

 

 

 

Page 53 Page 55
Image 54
Page 53 Page 55
Contents User Guide Important Notice Safety and Hazards Limitation Liability Patents Copyright Trademarks Qualcomm 3GSupport@sierrawireless.com Contact InformationRevision History Revision Release Changes Number DateContents Configuring your Raven Configuring Modbus/BSAP Contents Contents Contents Circuit Switch Communications Introduction to the Raven AleosAceWare AceManagerSimplified Deployment Monitor and ControlAceNet AceViewNetwork Monitoring Setup Wizard Modem DoctorModem Doctor USB Modem DoctorConnecting to the Telus Network Steps of a connectionConnecting to the Internet Dynamic vs. Static IP Addresses1x Communication SecuritySpecifications Power Connector Interface Port Pin-OutsSetup Wizard Starting the Setup WizardActivating your Raven on the 3 Telus Network Connecting to the Modem Setup WizardSetup Wizard Connected Selecting TasksOptionalUpdate Aleos Aleos UpdateSetup Wizard Activation Code Activate ModemSetup Wizard MDN and MIN/MSID Test Modem Setup Setup Wizard Signal TestOptional Setting up a DUN Connection 10 Setup Wizard DUN driver12 Setup Wizard DUN connections Activating Using AT Commands 14 Setup Wizard DUNAT*PROVISION2=MSL,MDN,MIN/MSID,SID,NID Raven 20070914 Hardware Installation Raven MountingConnecting to Power Connecting to a Computer or other Device Indicator LightsMounting Light PatternsOptional Mounting Bracket Hardware Installation of the Raven Rev 3.0B Feb.08 Hardware Installation of the Raven Rev 3.0B Feb.08 Configuring your Raven Using AceManagerStart AceManager Connect to your Raven AceManager Connect to ModemEnter the configuration options AceManager ConnectedUsing Templates Write the changes to the modemCreating the Template with AceManager · Cellular Technology specific settings the CDMA/EV‐DO group Reset the modem Applying a Template to one modem with AceManagerConfiguring your Raven 10 AceNet Selected modems Using a Terminal Application with AT Commands Choose a name and icon for your connectionPort Settings serial only Connect ToConnected · Flow Control HardwareAT Commands Data Communication and Host 6 Modes Basic ModesSerial Modes Start up Mode Basic ModesData Communication AT Mode PassThru Mode AceManager PassThruTelnet Mode Serial ModesAT\APPP UDP and UDP Pad UDP Auto AnswerReliable UDP UDP Multicast Mode TCP and TCP PadHybrid Modes TCP Auto AnswerUdplast Public and Private Mode Data CommunicationKeepalive Configuring Keepalive Data usage using KeepaliveIpping IP Manager Reasons to contact the modem and/or the connected deviceUnderstanding Domain Names Dynamic Names Car54.mydomain.comCar54.mydomain.com.ca Using IP Manager with your Raven AceManager Dynamic IPData Usage for IP Manager Server Updates Eairlink.comRestrictions for Modem Name Configuring DNS Understanding DNSPPP-Peer Domain Name AceManager DNSTelemetry Configuring Modbus/BSAPModbus Overview Remote Terminal Unit RTUModbus TCP/IP Supervisory Control and Data Acquisition ScadaProgrammable Logic Controller PLC Raven Modbus on UDPConfiguring the Raven at Polling Host for Modbus on Configure the listening/device portsConfigure the default mode for start-up Configure IP addresses for the Modbus IDsOptional Dynamic IP Address Configuring the Remote Ravens for Modbus with UDP Configure the portsConfigure IP addresses for the host AceManager UDPConfigure other RTU settings AceManager DNS Raven 20070914 Snmp Simple Network Management Protocol Management Information Base MIBSnmp Traps Snmp Configuration Listening PortSecurity Level User Name and Password AceManager Change Password menu optionSnmp MIB Definition Sample Trap DestinationCommunity String Snmp Simple Network Management Protocol Snmp Simple Network Management Protocol Snmp Simple Network Management Protocol Display Responses Product ID Configuration Commands Info informationDEVICEID? NETPHONE?NETCHAN? StatusHOSTMODE? NETERR?Any other value Failure AT Commands Requiring PassThru mode +WHWV +ECIO?+GSN +WPRL?Common Misc Miscellaneous+++ Dmethodd.d.d.d/ppppp or Dmethod@name/ ppppp DS=nOPRG=n S53=methodd.d.d.d/pppppMethod= P UDP Method=T TCP Method=N Telnet =1‐65535 Serial D.d=IP addressS3=n S4=nS5=n =1‐2545 =2‐10 seconds=0‐255 Parity=O Odd Parity=E Even Parity=N None Parity=M MarkS51=n S50=n=tenths of a second S211=n+IPR=n \APPP\Qn $QCVAD=nNUMTOIP=n CTSE=nModemhispeed PPPNOCARRIER=n=seconds S0=nS7=n S60=n=0 ‐ =intervalHh=01 Slip Hh=02 PPP Hh=03 UDP Hh=04 TCP HOR=nMDhh Hh=33 BsapUALL=n S83=nDU=n UDPLAST=nD.d=IP address of domain server DNSUPDATE=nDynamic IP DNSUSER=d.d.d.dDOMAIN=name Name=domain nameIPMGRKEYn=key IPMGRUPDATEn=m PPP/EthernetMODEMNAME=name DHCPSERVER=n HOSTAUTH=nHOSTNETMASK=n.n.n.n String=password PassThruD.d=local or peer IP address of the modem CSX1=n String=AT commands\APASSTHRU PTINIT=string=1‐255 minutes RESETPERIOD=nPTREFRESH=n =1‐255 hoursEmail=email address Body=message body Pw= password=SMS/E‐mail server number SMTPSTATUS?Subject=message subject Cntsms DasmsIndex= index list 0, 1 Message= message number DAE=n OtherSSMS? DATZ=nD.d=IP address Name=domain name Resetcfg=15‐255 minutes Name=domain name Port=portHost=IP address Port=TCP port =1 On=minutes TELNETTIMEOUT=nFriends TPORT=nLogging FM=nD.d = IP address DBGIPLVL=n Telemetry/Addr ListDBGCOMMLVL=n DBGPPPLVL=nMVMSK=hh IPL=nMVLEN=n Hh=hex valueMVTYP=n Addr ListMVOPT=n RKEY=nHexid=ID D.d=IP address or name 1x/EV-DOId=ID D.d=IP address or name +CTA=nPROVISION=MSL,MDN/MIN,SID,NID ~NAMLCK=nnnnnnNnnnnn=6 digit unlock code PROVISION2=MSL,MDN,MIN,SID,NID+WMDN=num +WIMI=numSid=system ID Nid=network ID Nam=0 Min=phone number Msid=second numberCircuit Switch Communications B Configuring Circuit-SwitchAT Commands and the Command String Commands Specific to the Raven 1x C3210 and C3216 Commands Specific to the Raven 1x C3211Step by Step Configuration Raven LEDs in Circuit-Switched ModeCommon AT Commands Hardware Required Software RequiredConnect the modem to your computer Erase the internal memoryInformation Required for CDMA/1x only Rev 3.0B Feb.08 139 Activate the Raven Start All Programs AirLink Communications AceManager 3GConfigure serial port speed Save the serial settingConfigure the Raven using a AceManager template 12 AceManager DisconnectConfigure additional PassThru settings 15 AceManager LoadReset the Raven Save the configuration settingsConfigure the Raven for your equipment Test the Raven ConfigurationCommission the Raven Modem on Site 146 20070914 Windows Dial-up Networking C DUN Installing a modem driver for RavenInstall the driver Connect the RavenSelect the Modems tab Check Don’t detect my modem I will select it from a list Check Selected Ports Configure the driver Modem PropertiesCreating a Dial-Up Networking PPP Connection Modem Properties ModemCreate a new network connection 10 Windows Start menuSelect Connect to the Internet Select Set up my connection manually Rev 3.0B Feb.08 156 Rev 3.0B Feb.08 157 Configure the DUN connection 21 New Connection FinishCheck Show icon...when connected Rev 3.0B Feb.08 160 Select Advanced Connecting to the Internet Using DUN Start AceViewEnable the Connection Windows DUNStart the DUN session Select Dial to connect to the modem and the cellular networkWindows Dial-up Networking DUN Rev 3.0B Feb.08 165
Related manuals
Manual 176 pages 17.38 Kb Manual 36 pages 19.88 Kb Manual 203 pages 17.49 Kb

20070914 specifications

Sierra Wireless 20070914 is a cutting-edge wireless communication module designed for IoT applications, offering remarkable features and robust performance. This module represents a significant advancement in the realm of embedded wireless solutions, catering to a variety of industries including automotive, industrial automation, and smart cities.

One of the key features of the Sierra Wireless 20070914 is its support for multiple cellular standards, including LTE, which ensures high-speed data transfer and reliable connectivity. The module is designed to operate on various frequency bands, making it versatile and suitable for global deployment. This multi-band capability allows businesses to deploy their IoT solutions in different regions without modification, reducing time-to-market and deployment costs.

Another standout characteristic of the Sierra Wireless 20070914 is its comprehensive and seamless integration with cloud services. The module supports advanced cloud connectivity options, enabling real-time data processing and analysis, which is crucial for industries that rely on timely decision-making. This feature is particularly important in sectors like transportation and logistics, where real-time tracking and monitoring are essential.

The power efficiency of the Sierra Wireless 20070914 is noteworthy. It is engineered to operate optimally in low-power modes, making it ideal for battery-operated devices. This focus on energy efficiency ensures prolonged device lifecycles, supporting the growing demand for sustainable and eco-friendly technologies.

Moreover, the module includes encrypted communication features, enhancing security and protecting sensitive data transmissions. With the increasing prevalence of cyber threats, this security aspect is critical for businesses looking to safeguard their IoT applications from unauthorized access and data breaches.

In addition to these features, the Sierra Wireless 20070914 offers comprehensive development support, including software development kits (SDKs) and application programming interfaces (APIs). This makes it easier for developers to integrate the module into their existing systems, streamlining the development process and accelerating innovation.

Overall, the Sierra Wireless 20070914 stands out as a powerful solution for IoT connectivity, blending advanced technology, security, and efficiency. Its capabilities are designed to support the diverse needs of modern industries, paving the way for future innovations and advancements in wireless communication. As businesses increasingly turn to IoT for modernization, modules like the Sierra Wireless 20070914 will play a crucial role in enabling this transformation.
Top Page Image Contents