Mitsubishi Electronics M342i manual Using your mobile as a modem, Opening the infrared port

Page 19

Opening the infrared port

Opening the infrared port allows you to receive information via this port.

Once opened, the infrared port can be used for any kind of transfer (data, fax, file transfer,...). The infrared port is automatically closed after a while.

To open the infrared port,

1 Press OK. Select Tools.

2Select Infrared port.

3Select Open. A confirmation message then are displayed to confirm that the port is open.

Closing the infrared port

Closing the infrared port closes all infrared sessions.

To close the infrared port:

1 Press OK. Select Tools.

2Select Infrared port.

3Select Close.

The infrared port automatically closes if it remains unused for a while.

Transferring a name card via the infrared port

You can transfer a name card via the infrared port:

1 Place your mobile directly opposite the infrared port of the other device.

2Open the infrared port of the other device.

3Select the card you wish to transfer as explained in the section "Viewing and calling phone- book numbers", page 34.

4Select Options. Select Send by... Infrared port. The infrared port open and the transfer is performed.

Using your mobile as a modem

You can use your mobile as a modem for other devices (PC, PDA,...) via the infrared port (on both devices) or via a PC cable. In order to activate a connection, a standard modem driver must already be installed in the other appliance:

1 Install the PC cable or open the Infrared port on your PC or PDA.

2Install the modem driver.

3Configure the PC according to the instructions given with the modem driver. Please enter the following parameters:

-Flow control: Hardware

-Data Bits: 8

-Parity: No parity

-Stop Bit: 1 stop Bit

-Speed: 115200b/s

1.The PC cable may not be supplied with your mobile. Please ask your retailer for an M342i compatible PC cable.

2.The compatibility between GPRS and i-mode features is operator dependent.

Your mobile:

1 Plug in the PC cable (please refer to the Getting Started with your M342i booklet).

or:

1 Open your mobile Infrared port.

If your mobile is set to Modem mode, (Please see "Operation mode", page 68) all incoming calls are rejected. If your mobile is not set to Modem mode, your Internet connection may be interrupted by incoming calls.

Once both devices are ready, the Internet connection can be activated (without any action being performed on your mobile).

19-Tools

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Page Table of Contents Fun & media box Introduction IntroductionVehicle safety General safetyDeclaration of conformity AC/DC adaptor charger Care and maintenanceBattery use Emergency callsDisposing of waste packaging PC cableYour responsibility Security codesUsing this guide Using this GuideSettings Tegic edition mode Understanding the graphic display indicators iconsAlarm clock Vibrator alert Keypad lock Silent mode on Mute Auto-switch-off mode onMultitap edition mode Getting started Getting StartedPreparing the phone for operation Basic operationsStandby display Ending a callPress the On/Off key Holding your phone while making or receiving a callTurning the phone off Power saverCalendar ToolsDiary ToolsEvents in a defined period/All events or Delete all events To view weekly entriesTo view monthly entries Select View... and Month viewSelect Tasks list Select Current tasks or Elapsed tasks Alarm notificationTasks list Select Tasks listCurrency converter CalculatorSelect Calculator Select Currency converter Alarm clockSelect Alarm clock Infrared portClosing the infrared port Using your mobile as a modemOpening the infrared port Select Infrared portMoving messages to SIM MessagesReading a received sms message Reading stored sms messagesActivating or deactivating the message alert tone Forwarding messagesPreparing the phone to send SMS messages Multitap/multipress method Mode and byEntering text Or edited directly from the keypad. PressT9 method Multitap method Example To type CardPress OK and select Messages. Select Write new Fill in the To field see Sending a new SMS message,Editing a text model Creating text modelsSending a new SMS message Status request Select Message configSignature Outbox and SIM archive emitted messagesBroadcast cell broadcast CB messages Storage consumptionSelect Broadcast Broadcast language Activating/deactivating the alert toneCalls log Call timersSelect Call timers Calls & TimesReminder call duration Call timer resetCall costs management Balance information subscription dependentSelect Call costs Setting the credit limit subscription dependentCall costs resetting all costs to zero Select Call costs Select Display cost typeSelect Line selection Recorded callPhone names card PhonebookStoring names and telephone numbers PhonebookSelect SIM names Editing a phonebook or a SIM name cardSelect Copy all names Select Phone to SIM or SIM to phone Voice dialling Viewing and calling phonebook numbersSelect Voice dialling Creating a group of cards Free space in the phonebookSelect Voice dialling Select Delete all My numbers display My cardFixed dialling numbers Select Fixed dialling. Select Status ExportSelect Fixed Dialling Camera CameraMobile positioning Taking a pictureSelect Add name, then Phone names Storing/erasing your picture Adjusting your picturePress Options Select Self timer capture Self timerPictures browser FUN & Media BOXPictures Fun & Media boxReceiving images via the infrared port Send by Rename Set as DetailsCropping Downloading images via the i-modeMelody download MelodiesMelodies Select MelodiesSelect Speech note Games & applicationsSpeech notes Select Games & applicationsPress OK. Select Fun & Media box OthersPlay Record newStoring a received vcalendar Storage usedSending a vcard or a vcalendar by SMS Calendar/Network services Network ServicesCalendar Mode Mode menuMode profiles User interfaceMode applications Saved pages SettingsOpen To display the selected saved Select Send terminal info or press Adjusting textMail system Sending terminal infoComposing an MMS Once in the Mail sub-menuComposing an e-mail Edit menu 2/2Inbox ColorSpace SliceSelect Selective retrieval or press Mail system settings Select Valid or Invalid Quick access to i-mode basic featuresSelect Yes and/or No Select Receive attachment or pressTo download a melody To save a webpageSelect Save To display a savedSettings SettingsTones Select Welcome screen Select Ring, Ramping, Keys, Conversation or AlarmDisplay Select Idle screenSelect Keypad lock KeypadSelect Goodbye screen Select BacklightSelect Speed Dial Phone settingsSelect Phone settings Voice mailSelect Phone settings Select Auto features Auto featuresTime & date Select GSM Services GSM servicesSelect Phone settings Select Time & date Select Phone settings Select Default settingsCall waiting Always To divert all incoming voice calls When notSelect Status or Cancel Select GSM Services Select Call diverting Select Cancel allSelect GSM Services Select Sending my ID Select GSM Services Select Sending my ID Select My settingsCall barring Selecting manual searchSelecting automatic search Select AutomaticPhone lock code Security featuresSelect GSM Services Select Call barring Operation modePUK code Summary of code/password entry chartPIN code PIN2 codeGlossary AppendixAppendix Phone does not switch on Trouble shootingMobile is on but nothing is displayed Error messages No connection Low batteryNetwork busy Network not allowedRue de la Chataigneraie Cesson Sévigné France GuaranteeIndex IndexSMS Page Page Page MQ860P009Z02
Top Page Image Contents