Weslo WLTL49907.0 user manual Nectors are not Connected Prop, ERLY, the Console MAY be Damaged

Page 8

5. While a second person holds the console as-

 

 

 

 

5

 

sembly near the Handrail (20), attach the

 

 

 

 

 

ground wire to the indicated hole in the Handrail

 

 

 

 

 

 

with a Ground Screw (33).

 

 

 

 

 

 

Ground

 

 

 

 

Wire

 

 

 

 

33

 

 

 

 

Hole

 

 

 

 

20

 

 

 

 

 

Console

 

 

 

 

Assembly

6. While the second person continues to hold the

6

 

 

 

console assembly, locate the wire underneath

 

 

 

 

 

 

 

the console assembly.

 

 

 

 

Connect the wire from the console assembly to

 

 

 

 

the Wire Harness (77). See the inset drawing.

 

 

 

 

The connectors should slide together easily

 

 

Wire

77

and snap into place. If the connectors do not

 

 

 

 

slide together easily and snap into place, turn

 

 

 

 

one connector and then try again. IF THE CON-

 

 

 

 

NECTORS ARE NOT CONNECTED PROP-

Console

77

 

 

ERLY, THE CONSOLE MAY BE DAMAGED

 

 

WHEN THE POWER IS TURNED ON. Insert

Assembly

 

 

 

the connectors downward into the Handrail (20).

 

 

 

 

 

 

20

 

 

7. Set the console assembly on the Handrail (20).

7

 

 

 

Be careful to avoid pinching any of the

 

Console Assembly

 

 

 

 

wires. Make sure that the ground wire (see

Channel

 

 

 

step 5) and the wire from the console assem-

 

 

 

 

 

 

 

bly (see step 6) are in the indicated channel.

 

 

 

 

Hand tighten five Screws (3) into the Handrail

 

 

 

 

(20) and the console assembly. Do not put

 

 

 

 

Screws into the two indicated holes. Start all

 

 

 

 

five Screws, but do not tighten them yet.

 

 

 

 

 

 

 

20

 

 

 

3

3

3

 

 

 

 

 

 

No Screws

 

 

8

 

 

 

Image 8
Contents QUESTIONS? Model No. WLTL49907.0 Serial NoCall TOLL-FREE Mon.-Fri a.m.-6 p.m. MST Sat a.m.-4 p.m. MSTTable of Contents Important Precautions Page Before YOU Begin Leg. Firmly tighten the Extension Leg Bolts AssemblyMake sure that the power cord is unplugged Extension Leg. Firmly tighten the Extension Leg Bolts Do not let the Wire Harness 77 fall into Right UprightFrame 58 until the treadmill is com Pletely assembled Nectors are not Connected Prop ERLY, the Console MAY be DamagedMake sure that no wires are pinched PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired HOW to USE a Cross Trainer Program Select one of the six cross trainer programsPerform the first strength exercise when prompted Continue the cross trainer programInformation Mode Optional Chest Pulse SensorHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches R0707A Qty DescriptionExploded Drawing A-Model No WLTL49907 Exploded Drawing B-Model No. WLTL49907.0 R0707A Exploded Drawing C-Model No. WLTL49907.0 R0707A Exploded Drawing D-Model No. WLTL49907.0 R0707A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty