Weslo WLTL24090 user manual Left Upright 31. Do not tighten the Bolt yet, Yet

Page 6

3.Cut the plastic tie holding the cage nut in the upper end of the Left Handrail (30).

Position the Left Handrail (30) on the left Upright (31). Thread a 1/4Ó x 1Ó Bolt (23) with a Handrail Washer (51) two complete turns into the upper end of the left Upright and the Left Handrail. Do not tighten the Bolt yet.

Thread a 1/4Ó x 1Ó Bolt (23) with a Handrail Washer (51) two complete turns into the lower end of the Left Handrail

(30)and the left Upright (31). Do not tighten the Bolt yet.

4.With the help of a second person, lift the Right Handrail

(32)and hold the Right Handrail and the Console Base

(12)near the right Upright (31) as shown. Feed all of the excess Wire Harness (28) into the Right Handrail, through the indicated bracket, and down into the right Upright; bend the Wire Harness, if necessary.

Cut the indicated plastic tie off the Right Handrail (32).

Make sure that the Wire Harness (28) is in the bracket and insert the bracket into the right Upright (31). Make sure that the Wire Harness is not pinched.

5.Thread a 1/4Ó x 1Ó Bolt (23) with a Handrail Washer (51) two complete turns into the upper end of the right Upright (31) and the Right Handrail (32). Do not tighten the Bolt yet.

Thread a 1/4Ó x 1Ó Bolt (23) with a Handrail Washer (51) two complete turns into the lower end of the Right Handrail

(32)and the right Upright (31). Do not tighten the Bolt

yet.

6.Set the Console Base (12) on the Handrails (30, 32). Make sure that the Wire Harness (28) is out of the way as you thread four 1 1/4Ó Screws (20) into the Handrails and the Console Base.

Tighten all parts used in steps 3 and 5. Then, tighten the 1 1/4Ó Screws (20) used in this step.

3

 

 

 

 

23

 

 

 

 

51

 

 

 

 

30

 

 

31

 

 

 

51

23

 

 

 

4

 

 

 

 

12

 

 

 

Bracket

Plastic Tie

 

 

 

32

28

 

 

 

 

 

 

31

 

5

 

 

 

 

 

 

23

 

32

51

 

 

 

 

 

 

31

 

 

23

 

 

 

 

51

 

6

28

 

 

32

 

 

 

 

20

12

 

 

 

 

 

31

30

20

 

 

7.Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or car- pet, place a mat under the treadmill.

6

Image 6
Contents QUESTIONS? Model No. WLTL24090 Serial NoCustomer HOT Line Table of Contents Important PrecautionsPage Front Before YOU BeginBack Right SideAssembly Left Upright 31. Do not tighten the Bolt yet YetOperation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Insert the key fully into the power switch Diagram of the ConsoleBattery Installation Step by Step Console OperationMeasure your pulse, if desired Reset the console and start the walking beltFollow your progress with the monitor display Pulse will not be Detected. NextHOW to Fold and Move the Treadmill HOW to Change the Incline of the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the Treadmill HOW to Lower the Treadmill for USEMaintenance and TROUBLE-SHOOTING Problem The power turns off during useTop View 2ÓÐ3Ó Conditioning Guidelines Exercise IntensityWorkout Guidelines Suggested Stretches Part LISTÑModel No. WLTL24090 Qty DescriptionExploded DRAWINGÑModel No. WLTL24090 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT