Weslo WLTL 13921 user manual Maintenance and Troubleshooting, Symptom the Walking Belt does not

Page 8

MAINTENANCE AND TROUBLESHOOTING

Most problems can be solved by following the simple steps below. If further assistance is needed, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

1. SYMPTOM: THE CONSOLE DOES NOT

3. SYMPTOM: THE WALKING BELT SLIPS OR IS

FUNCTION PROPERLY

 

OFF-CENTER

a. Replace the batteries in the console (see assem-

a. If the walking

bly step 5 on page 5).

 

belt slips

 

 

 

when walked

b. Make sure that the reed switch is properly adjust-

on, use the

ed (see assembly step 4 on page 5).

allen wrench to

 

 

 

turn both

c. Make sure that the reed switch wire is plugged

adjustment

fully into the back of the console (see assembly

bolts clockwise,

step 3 on page 4).

 

 

1/4 of a turn. When the walking belt is correctly

 

 

 

tightened, you should be able to lift each side of

d. The console, like most electronics, is susceptible

the walking belt 2 to 3 inches. Walk on the tread-

to static electricity build-up caused by certain

mill for a few minutes. Repeat until the walking

types of clothing or by the operation of the tread-

belt is properly tightened. Be careful to keep the

mill. If the display is blank or gives incorrect read-

walking belt centered.

ings, apply an anti-static spray to the handrail.

 

Anti-static spray is available where laundry sup-

b. If the walking

plies are sold.

 

 

belt has shift-

 

 

 

ed to the left

2. SYMPTOM: THE WALKING BELT DOES NOT

side, use the

MOVE SMOOTHLY

 

 

allen wrench to

 

 

 

turn the left

a. If the walk-

 

 

adjustment bolt

ing belt is

 

Walking Belt

clockwise, and

overtight-

 

 

the right adjustment bolt counterclockwise, 1/4 of

ened, per-

 

 

a turn each. Be careful not to overtighten the

formance

 

 

walking belt. Walk on the treadmill for a few min-

may be

 

 

utes. Repeat until the walking belt is centered.

reduced and

2"–3"

 

 

the walking

Bolts

c. If the walking

 

belt may be

 

belt has shift-

 

 

permanently

 

 

ed to the right

damaged. Using the allen wrench, turn both rear

side, use the

roller adjustment bolts counterclockwise 1/4 of a

allen wrench to

turn. When the tension of the walking belt is cor-

turn the left

rect, you should be able to lift each side of the

adjustment bolt

walking belt 2 to 3 inches. Walk on the treadmill

counterclock-

for a few minutes. Repeat until the walking belt is

wise, and the right adjustment bolt clockwise, 1/4

properly tightened. Be careful to keep the walking

of a turn each. Be careful not to overtighten the

belt centered.

 

 

walking belt. Walk on the treadmill for a few min-

 

 

 

utes. Repeat until the walking belt is centered.

8

Image 8
Contents Customer HOT Line QUESTIONS?Model No. WLTL13921 Serial No Table of Contents Important PrecautionsBefore YOU Begin Long Pins are fully inserted at the same level AssemblyScrewdriver and an adjustable wrench not included Do not fully tighten the Screw yet Turn on the power Treadmill OperationLubricating the Walking Platform Follow your progress with the five modesLowering the Treadmill for USE Incline AdjustmentFolding the Treadmill for Storage Move Smoothly Maintenance and TroubleshootingSymptom the Walking Belt does not WHY EXERCISE? HOW to Measure Your Heart RateConditioning Guidelines Exercise IntensityExercise Frequency Qty DescriptionExploded DRAWING-Model No. WLTL13921 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty