Weslo WCTL41305.0 Careful not to pinch the wires. Insert two 2 3/4 Bolts, Able to turn freely

Page 7

2. Identify the Right Upright (10). Note: The Left Upright (9)

has the Latch Housing (77, see step 3) attached to it.

Have a second person hold the Right Upright (10) near the

Base (82) as shown. Orient the Right Upright so that it is

angled forward (see step 3). Feed the Upright Wire

Harness (17) into the lower end of the Right Upright and

out of the upper end.

Next, hold the Right Upright (10) against the Base (82). Be

careful not to pinch the wires. Insert two 2 3/4” Bolts

(47), with two Washers (29) and two Star Washers (81),

into the Base, and loosely thread the Bolts into the lower

end of the Right Upright (10).

Attach a Wheel (95) to the Base (82) with a Wheel Bolt (86).

Do not overtighten the Wheel Bolt; the Wheel must be

able to turn freely.

With the help of a second person, tip the treadmill onto its

right side. Be careful not to damage the Upright Wire

Harness (17). Have a second person hold the Left Upright

(9) near the Base (82). Orient the Left Upright so that it is

angled forward (see step 3). Attach the Left Upright and

the other Wheel (not shown) as described above. Note:

There are no wires in the Left Upright.

3. With the help of a second person, set the treadmill on the

floor with the Left and Right Uprights (9, 10) vertical.

Identify the Right Handrail (93), which has a large hole in

the left side. Feed the Upright Wire Harness (17) up

through the hole in the bottom of the Right Handrail and

out of the large hole in the left side. Note: It may be help-

ful to use needlenose pliers to pull the Wire Harness out

2

 

 

 

 

10

 

17

 

 

 

86

47

81

 

29

95

 

 

 

 

9

 

82

 

 

81

 

47

 

 

 

29

 

3

56

 

 

 

 

 

17

123

56

of the large hole.

Set the Right Handrail (93) on the Right Upright (10).

Finger tighten a 4” Bolt (120) through the Right Upright into

the lower end of the Right Handrail. Attach the upper end

of the Right Handrail with a 2 1/2” Bolt (56). Do not

tighten the Bolts yet.

Attach the Left Handrail (123) as described above. Note:

There is not a wire in the Left Handrail.

9

77

120

Large

Hole

93

10

120

7

Image 7
Contents Model No. WCTL41305.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Back Right Side Before YOU BeginMake sure that the power cord is not plugged AssemblyAble to turn freely Careful not to pinch the wires. Insert two 2 3/4 BoltsRight side. Be careful not to damage the Upright Wire Do not overtighten the Wheel Bolt the Wheel must beRack Bolts and Nuts before tightening any of them Bolts yetTop View HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate, if desiredWhenkey. you are finished exercising, remove Select a speed program HOW to USE a Speed ProgramWhen the program is completed, remove Key from the console Insert the key fully into the consoleHOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoAdapter Audio Cable HOW to Connect Your VCRWhenkey. the program is completed, remove PressVCR. the Play button on your CD player orFollow the on-line instructions to start Program HOW to USE Programs Directly from OUR WEB SiteReturn to the treadmill and stand on the foot Information Mode HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked on Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Key Qty Description R0705AModelNo ExplodedExploded DRAWING-Model No. WCTL41305.0 Part 2 R0705A Exploded DRAWING-Model No. WCTL41305.0 Part 3 R0705A Limited Warranty HOW to Order Replacement Parts