Weslo 831.295020 Maintenance and Troubleshooting, Problem The power turns off during use

Page 12

MAINTENANCE AND TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call toll-free 1-800-4-MY-HOME®(1-800-469-4663).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppres- sor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge sup- pressor that meets all of the specifications described on page 8. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the circuit breaker located on the treadmill frame near the power cord. If the switch pro- trudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key fully into the console.

d.If the treadmill still will not run, please call toll-free 1-800-4-MY-HOME®(1-800-469-4663).

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from the hood. Note each hole the screws are removed from. Carefully remove the hood. Locate the Reed Switch

(13)and the Magnet (63) on the left side of the Pulley

(75).Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw (89), move the Reed Switch slightly, and then retighten the Screw. Re- attach the hood, making sure that the screws are tightened into the original holes. Run the treadmill for a few minutes to check for a correct speed reading.

a

1/8”

75

28

 

13

63

 

Top

View

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Assembly Operation Maintenance Part List and Drawing Model No Serial NoTable of Contents Important PrecautionsPage Before YOU Begin FrontBack Right SideAssembly Assembly requires the included allen wrenchesExtension Leg Screw while tightening it Harness Touch the right Handrail 4 to discharge any staticPage Operation and Adjustment HOW to Plug in the Power CordPerformant Lubetm Walking Belt Diagram of the Console STEP-BY-STEP Console OperationInsert the key fully into the console Pressbelt. the Speed button to start the walkingChange the incline of the treadmill as desired Follow your progress with the displays Time/DistanceCalories/Speed Whenkey. you are finished exercising, removeHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USEMaintenance and Troubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on HOW to Measure Your Heart Rate Conditioning GuidelinesExercise Intensity Workout GuidelinesTraining Zone Exercise Cool-downExercise Frequency Part Identification Chart Qty Description If a part is missing, call toll-free295020 Full 90 DAY Warranty Sears, Roebuck and Co., Dept WA, Hoffman Estates, IL
Top Page Image Contents