® |
|
| CAT EYE VELO5 |
|
| CATEYE VELO 5 | CAT EYE VELO8 |
|
| ||
|
|
| CYCLOCOMPUTER |
|
|
| Model |
|
|
| English |
|
|
|
|
U.S. Pat. Nos. 4642606, 5236759 and Pat. Pending
Copyright© 2003 CAT EYE Co., Ltd.
VELO 5 | VELO 8 |
| |
CATEYE VELO 5 | CATEYE VELO 8 | SET | |
(on Back) | |||
|
|
F
G
MODE 
Caution
•Do not concentrate on the computer operations while riding. Always be sure to ride safety.
•Be sure to securely mount the magnet, sensor and bracket on your bicycle, and periodically check to see if any parts have loosened.
•Used batteries are harmful if swallowed by mistake. They must be disposed in accordance with local regulations.
•Do not leave the main unit exposed to direct sunlight. Never disassemble the main unit.
•For cleaning of the main unit or accessories, use diluted neutral detergent on a soft cloth, and then wipe it off with a dry cloth. Do not use paint thinner, benzine or alcohol since such chemicals may damage the surface.
Package Contents
1Bracket
2 Wire
3 Sensor
4 Magnet
5 Nylon Ties 7
IMPORTANT!
Correct positions of the sensor and the magnet:
AWhen rotating the front wheel, the magnet's 4center must be aligned with the sensor's 3marking line.
BThe distance between the sensor 3 and the magnet 4must be less than 5mm.
Name of Parts |
|
Speed | 0.0 (4.0) to 299.9 km/h [0.0 (3.0) to 185.0 mph] |
Mode Symbol | Indicates the mode currently selected. |
| (The corresponding value is indicated on the lower line.) |
Pace Arrow* | Indicates if the current speed is faster or slower than the average speed. |
| ( Faster Slower) |
Speed Scale
Sub Display (selected function)
Battery Case Cover
Contact
*The Pace Arrow feature is only available on the VELO8. Pace Arrows are not displayed on the VELO5.
Display function
• Tm* | [Elapsed Time] | 0:00'00" to 9:59'59" |
• Dst | [Trip Distance] | 0.00 to 999.99 km [mile] |
• Av* | [Average Speed] | 0.0 to 299.9 km/h [ 0.0 to 185.0 mph] |
|
| (Measurable up to 27 hrs or 999.99 km/h) |
• Mx | [Maximum Speed] | 0.0 (4.0) to 299.9 km/h [0.0(3.0) to 185.0 mph] |
• Cal* | [Calorie Consumption] | 0.0 to 9999.9 kcal (estimated from speed data) |
• Odo | [Total Distance] | 0.0 to 9999.9 km [mile] |
• | [Clock] | 0:00' to 23:59'[1:00'to 12:59'] |
* This feature is only available on the VELO8. No measurement is done on the VELO5.
Start/Stop of Measuring
The unit starts measuring automatically when you start pedaling, and stops measuring when your come to a stop. The upper display always shows the Current Speed.
Shift of Lower Display
Each time you press the MODE button, a different data value appears on the lower line. e
Power Saving Function
If the main unit does not receive a signal after about 10 minutes, the main unit enters Power Saving Mode and displays the clock count only. To re turn to normal display, press the MODE button or start your bicycle again to cancel the Power Saving function.
Data Reset
When a screen with the Reset mark in the OPERATION FLOW is displayed, continue pressing the MODE button and the measured data will return to zero. However, the Odometer (total distance) and Clock do not return to zero.
How to Set Clock
In the clock mode, press SET button on the back, and the display enters clock setting mode. *If Km/h has been selected for speed scale, it becomes
If mph has been selected, it becomes
INSTALLING THE UNIT
6
2
3
A |
3
4
B |
6
3
5mm
How to Change Tire Size
Display the Total Distance (Odo) and press the SET button to change the tire size. You can select a tire size in two ways: Either select from among preset sizes c or enter the tire’s circumference directly in increments of 1 cm. d
Maintenance
•If the contact of the unit or the bracket gets wet, dry it off with a cloth. If they become rusty, it will cause speed detection error.
•If the gaps between the buttons and the unit get clogged with mud or sand, wash them away with water.
Troubleshooting
No display.
Has the battery in the main unit run down?
Replace it with a new one.
Incorrect data appears.
Do all clear operation.
Current speed does not appear.(First,
Is the clearance between the sensor and the magnet too large? Are the magnet's center and the sensor's marking line aligned?
Is the cord broken?
Even if the outside of the cord looks normal, there could be damage.
Replace the bracket and sensor set with a new one.
1 | 2 | 3 |
4
3 3 
5
4 | 5 |
1
Is there anything sticking on the contact of the main unit or the bracket?
Clean the contact with a cloth.
Current speed disappears when using in the rain.
Wipe any water or dirt from the contacts and apply a water repellent silicon grease. Do not apply standard grease,
as it may cause damage to the bracket.
Replacing Battery
If the screen becomes dim, it is the time to replace the battery. g *Insert a new lithium battery (CR2032) with the (+) mark facing up.
1 After replacing the battery, perform the
Specification
Battery | Lithium Battery CR2032 x 1(battery life: approx. 3 years) |
| (*The life of the |
Microcomputer | |
Display | Liquid crystal display |
Sensor | |
Tire Sizes | Tire sizes of 16, 18, 20, 22, 24, 26, 700C, and 27 inches, or tire peripheral lengths from 100 to 299 |
| cm (Initial value: 26 in.) |
Working Temperature | 0°C - 40°C |
Length of Wire | 70cm |
Dimension/Weight |
*The specifications and design are subject to change without notice.
●CalorieConsumption*1(VELO8)
The calorie consumption data is only the accumulated value that is calculated from the speed data of every second. It differs from the actual consumed calorie.
16
5
7
Click
SETTING
km/h
Speed | 10 km/h | 20 km/h | 30 km/h |
Kcal per hour | 67.3 kcal | 244.5 kcal | 641.6 kcal |
mph |
|
|
|
|
|
|
|
Speed | 10 mph | 20 mph | 30 mph |
Kcal per hour | 155.2 kcal | 768.2 kcal | 2297.2 kcal |