Image IMTL39606.3 user manual Troubleshooting, Problem The power turns off during use, Top

Page 20

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 11. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the two Foot Rail Screws

(4)and the two Hood Screws (86) and carefully re- move the Hood (1).

a86

4

1 4

Locate the Reed Switch (63) and the Magnet (67) on the left side of the Pulley (64). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8". If necessary, loosen the 3/4” Tek Screw (38), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown), and run the treadmill for a few minutes to check for a correct speed reading.

1/8"

64

38

 

63

67

Top

 

View

 

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents QUESTIONS? Model No. IMTL39606.3 Serial NoCall TOLL-FREE Mon.-Fri., 6 a.m.-6 p.m. MSTTable of Contents Important Precautions Page Before YOU Begin Back Right SideAssembly Tighten the Upright Bolts yetUpright Wire 28 does not fall into the Right Upright 33, and a Nut 47 do not tighten the Frame Bolt yet Outer side of the Frame Spacer facingFrame Bolt yet Upright Wire Front ViewDo not overtighten the Frame Bolts Side View View from AbovePRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power Step ProgramHOW to USE the Manual Mode Always walk at a speed that is comfortable for you Measure your heart rate if desiredTurn on the fan if desired Whenkey. you are finished exercising, removeSelect a step program HOW to USE a Step ProgramWhen the program is completed, remove Key from the console HOW to USE a Calorie Goal Program Press the Start button to start the programInformation MODE/DEMO Mode HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Top TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on Conditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Part LIST-Model No. IMTL39606.3 Key No. Qty DescriptionExploded DRAWING-Model No. IMTL39606.3 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT HOW to Order Replacement PartsLimited Warranty
Top Page Image Contents