Image IMTL94106.2 user manual Troubleshooting, Problem The power turns off during use

Page 23

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 10. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five min- utes and then press the switch to the reset position.

Tripped Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch to the reset position.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console and then reinsert it.

d.Make sure that the reset/off circuit breaker is in the on position (see the drawing above).

e.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 10.

b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may be permanently damaged. Remove the key and UNPLUG THE POWER CORD. Using the included hex key, turn both rear roller bolts counterclockwise 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 3 to 4 inches off the walking plat- form. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key and run the tread- mill for a few minutes. Repeat until the walking belt is properly tightened.

b

3–4”

 

Rear Roller Bolts

 

c. If the walking belt still slows when walked on, see the front cover of this manual.

23

Image 23
Contents Mon.-Fri., 6 a.m.-6 p.m. MST QUESTIONS?Model No. IMTL94106.2 Serial No Call TOLL-FREETable of Contents Important Precautions Page Power Lines Service Right Side Before YOU BeginAssembly Page HOW to Connect AN External Source Using a Catv Cable HOW to Connect a 75 OHM Catv CablePRE-LUBRICATED Walking Belt HOW to Plug in the Power CordTreadmill Operation Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate if desiredSelect a preset program HOW to USE a Preset ProgramSee on pages 12 Select a custom program HOW to Create a Custom ProgramHOW to USE a Custom Program Enter your age HOW to USE a Heart Rate ProgramSelect a heart rate program Hold the handgrip pulse sensor HOW to USE the Information Mode HOW to Operate the Personal TelevisionPress the Power button to turn on Television Press the Volume buttons to adjust the volumeHOW to Adjust the Cushioning System Press the Power button again and select a Cable connectionHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The walking belt slows when walked on TroubleshootingProblem The power turns off during use Top View Problem Television reception is poor Problem The displays of the console do not function properlyExercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesQty Description R1207AQty Exploded Drawing Exploded DRAWING-Model Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty