NordicTrack NTTL90081 manual Symptom the Walking Belt is OFF-CENTER When Walked on

Page 16

4. SYMPTOM: THE WALKING BELT IS OFF-CENTER WHEN WALKED ON

a. If the walking belt has shifted to the left, first remove the key

and UNPLUG THE POWER CORD. Using the included allen wrench, turn the left rear roller adjustment bolt clockwise, and the right bolt counterclockwise, 1/4 of a turn each. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered.

b. If the walking belt has shifted to the right, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn the left rear roller adjustment bolt counterclockwise, and the right bolt clockwise, 1/4 of a turn each. Be careful not to over- tighten the walking belt. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered.

c. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller adjustment bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift the edges of the walking belt 3 to 4 inches off the walking plat- form. Be careful to keep the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few min- utes. Repeat until the walking belt is properly tightened.

a

b

c

5.SYMPTOM: THE WALKING BELT SLOWS WHEN WALKED ON

a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.

b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may be permanently damaged. Remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller adjustment bolts counterclock- wise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift the edges of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is prop- erly tightened.

b

3Ð4Ó

Rear Roller Adjustment Bolts

c. If the walking belt still slows when walked on, please contact our Customer Service Department.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model No. NTTL90081 Serial No Questions?Customer HOT Line Table of Contents Important Precautions There is one decal On each side Before You Begin Assembly Treadmill Operation HOW to Plug in the Power CordPerformant Lubetm Walking Belt Diagram of the Console Features of the ConsoleHOW to USE the Manual Mode Plug in the power cordSelect the Manual mode Insert the key fully into the consoleWhen you are finished exercising, stop Speed displayINCLINE/DISTANCE display Walking belt and remove the keyHOW to USE the Incline Programs Select one of the Incline programsFollow your progress with the four displays From the consolePage HOW to Fold the Treadmill for Storage How to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Maintenance and Trouble-shooting Symptom the Power does not Turn onSymptom the Power Turns OFF During USE Symptom AN Error Code ÒE1Ó or ÒE6Ó Appears on the ConsoleSymptom the Walking Belt is OFF-CENTER When Walked on Symptom the Walking Belt Slows When Walked onSymptom the Displays of the Console do not Function Properly TopConditioning Guidelines Factors in a Sensible DietExercise Steps Target Heart Rate ZonesWarm up before you begin Weight Loss TipsStretch after your warm-up Get FIT with the PowerTread Benefits of Aerobic ExerciseCool down after aerobic exercise Stretchsession.again at the end of your exerciseWorkout Tips Workout ProgramsPart ListÑModel No. NTTL90081 Key No. Qty DescriptionOrdering Replacement Parts Exploded DrawingÑModel No. NTTL90081 Exploded DrawingÑModel No. NTTL90081 Limited Warranty
Top Page Image Contents