NordicTrack NTL27005.0 Troubleshooting, Problem The power turns off during use, Top View

Page 24

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor that meets all of the specifications described on page 9. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the reset/off circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

PROBLEM: The power turns off during use

c

Tripped

Reset

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the

circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key fully into the console.

d.Make sure that the reset/off circuit breaker is in the reset position.

e.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and unplug the power cord. Remove the indicated Screws (69) from the Hood (37). Carefully rotate and lift the Hood.

Locate the Reed Switch (20) and the Magnet (107) on the left side of the Pulley (10). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw (109), move the Reed Switch slightly, and then retighten the Screw. Then, reattach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

a

37

69

 

69

1/8”

 

109

10

20

107

 

Top

 

View

 

24

Image 24
Contents QUESTIONS? Model No. NTL27005.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Operation and AdjustmentPage Before YOU Begin Left SideRight Side Assembly Page HOW to USE the Chest Pulse Sensor HOW to PUT on the Chest Pulse SensorChest Pulse Sensor Care and Maintenance Chest Pulse Sensor TroubleshootingOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired Avoid movingTurn on the fans if desired HOW to USE a Preset Program Select one of the preset programsAdjust the intensity level of the program if Desired See on HOW to USE a Distance Program Select a distance programPress the Start button to start the program HOW to Connect Your MP3 Player or CD Player HOW to Connect Your Portable StereoAudio Cable HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR PressVCR. the Play button on your CD player orMeasure your heart rate if desired Directly from OUR WEB Site Follow the on-line instructions to start ProgramReturn to the treadmill and stand on the foot Information MODE/DEMO Mode Important If aHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Problem The chest pulse sensor does not function properly Conditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Page R1005B Qty DescriptionOrdering Replacement Parts Exploded DRAWING-Model No. NTL27005.0 120 Limited Warranty