NordicTrack NTL27005.0 user manual Assembly

Page 6

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials, unless otherwise instructed. Do not dispose of the packing materials until assembly is completed. Assembly requires

the included allen wrench and your own flat-bladed screwdriver , wire cutters ,

and adjustable wrench .

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the treadmill or the shipping carton. This is a normal con- dition and does not affect treadmill performance. If there is lubricant on top of the walking belt or foot pads, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

1.With the help of a second person, carefully raise both Uprights (83) to a vertical position. Remove any packag- ing from the crossbar.

Remove the elastic holding the Upright Wire Harness

(131)in the right Upright (83). Have a second person hold the Handrails (73) near the Uprights. Connect the Upright Wire Harness to the wires extending from the Console Base (120). The connectors should slide to- gether easily and snap into place. If they do not, turn one connector and try again. Insert the connectors and the Upright Wire Harness into the hole in the right Upright. Then, set the Handrails on the Uprights, being careful not to pinch the wires.

2.Insert two 4 1/2” Bolts (96) with Handrail Spacers (95) into the right Upright (83). Next, lift the right Handrail (73) slightly and align the Handrail Bolts with the holes in the Handrail. Thread the Handrail Bolts into the Handrail. Do not tighten the Handrail Bolts yet. Be careful not to pinch the wires.

Attach the left Handrail (not shown) in the same way. Make sure that the Handrail Spacers (95) are flush against the Uprights (83), with the thick sides facing the center of the treadmill, as shown in the inset drawing. Then, tighten all four Handrail Bolts (96).

3.With the help of a second person, carefully tip both Uprights (83) to the floor.

Insert the three Cage Nuts (28) into the three indicated holes in the treadmill.

To insert each Cage Nut (28), first hook one side of the Cage Nut into a hole and then use a flat-bladed screw- driver to press the other side into the hole, as shown.

1

120

 

 

131

 

83

73

Crossbar

 

2

 

 

83

 

95

73

 

 

Thick

 

Side

 

95

 

96

3

 

 

83

 

28

 

28

6

Image 6
Contents QUESTIONS? Model No. NTL27005.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Operation and AdjustmentPage Before YOU Begin Left SideRight Side Assembly Page Chest Pulse Sensor Care and Maintenance HOW to USE the Chest Pulse SensorHOW to PUT on the Chest Pulse Sensor Chest Pulse Sensor TroubleshootingOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired Avoid movingTurn on the fans if desired HOW to USE a Preset Program Select one of the preset programsAdjust the intensity level of the program if Desired See on HOW to USE a Distance Program Select a distance programPress the Start button to start the program HOW to Connect Your MP3 Player or CD Player HOW to Connect Your Portable StereoAudio Cable HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR PressVCR. the Play button on your CD player orMeasure your heart rate if desired Directly from OUR WEB Site Follow the on-line instructions to start ProgramReturn to the treadmill and stand on the foot Information MODE/DEMO Mode Important If aHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Problem The chest pulse sensor does not function properly Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Page R1005B Qty DescriptionOrdering Replacement Parts Exploded DRAWING-Model No. NTL27005.0 120 Limited Warranty