JVC SP-UXV100, CA-UXV100, UX-V100 manual Troubleshooting, Symptom, Possible Cause, Action

Page 25

Troubleshooting

•If you are having a problem with your System, check this list for a possible solution before calling for service.

•If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as your dealer, for service.

Symptom

No sound is heard.

Poor radio reception

The CD does not play.

The CD skips.

The CD cover does not open or close.

The cassette holder cannot be opened.

Unable to record.

Operations are disabled.

Unable to operate the Remote Control.

Possible Cause

•Connections are incorrect, or loose.

•Headphones are connected.

•Antennas are disconnected.

•The AM Loop Antenna is too close to the System.

•The FM Wire Antenna is not properly extended and positioned.

The CD is upside down.

The CD is dirty or scratched.

The AC power cord is not plugged in.

During tape playing, the power cord was unplugged.

Cassette record protect tabs are removed.

The built-in microprocessor has malfunctioned due to external electrical interference.

•The path between the Remote Control and the sensor on the Unit is blocked.

•The batteries have lost their charge.

Action

•Check all connections and make corrections. (See pages 2 – 5.)

•Disconnect the headphones.

•Reconnect the antenna securely.

•Change the position and direction of the AM Loop Antenna.

•Extend FM Wire Antenna to the best reception position.

Put the CD in with the label side up.

Clean or replace the CD.

Plug the AC power cord.

Plug in the power cord, press the button, and then press the TAPE 0button.

Cover the holes on the back edge of the cassette with adhesive tape.

Unplug the System then plug it back in.

•Remove the obstruction.

•Replace the batteries.

21

EN10-22.UX-V100[B]f

21

12/12/00, 12:34 PM

Image 25

Contents UX-V100- Consists of CA-UXV100 and SP-UXV100 Micro Component SystemReproduction of Labels If in Doubt Consult a Competent ElectricianClassification LABEL, Placed on Rear Enclosure Class 1 Laser ProductUX-V100 Above ALL Table of Contents How to Put Batteries in the Remote Control AccessoriesUsing the Remote Control Getting StartedConnecting the AM MW/LW Antenna Connecting the FM AntennaUsing the supplied Wire Antenna Using the coaxial type connector not suppliedConnecting External Equipment Connecting the SpeakersLine in AUX On the Unit On the Remote Control Connecting the AC Power CordAdjusting the Volume Turning the Power On and OffCommon Operations Turning the System onAdjusting the treble level Adjusting the bass levelReinforcing the Bass Sound AHB PRO Controlling the Tone Bass/ TrebleTuning In a Station Using the TunerPresetting Stations Presetting stations manuallyPresetting stations automatically Changing the FM Reception ModeTo restore the stereo effect, press the FM Mode button on Press the SET button within 5 secondsInserting a CD Using the CD PlayerUnloading a CD Quickest way to start a CD is with the one touch operationPrograming the Playing Order of the Tracks Basics of Using the CD Player Normal PlayPress the Repeat button on the Remote Control Press the Random button on the Remote ControlPlaying at Random Repeating TracksReverse Mode Using the Cassette Deck Listening to a TapeStandard Play One touch playStandard Recording Using the Cassette Deck RecordingThings to know before you start recording Check the recording direction for the tapeOne track recording CD Direct RecordingPress the CD #/8 button twice To stop at any time during the recording process, pressAUX AHB PRO Volume + Using External EquipmentListening to External Equipment To exit from AUX mode, select another sourceSetting the Daily Timer Using the TimersSetting the Clock Setting the Recording Timer Insert a blank or erasable tape into the Cassette Deck Setting the Sleep TimerCare and Maintenance Symptom TroubleshootingPossible Cause ActionSpecifications 1200MWMMDWJEM