Healthrider HRTL10982 TROUBLE-SHOOTING and Maintenance, Problemsolution, Power does not turn on

Page 17

TROUBLE-SHOOTING AND MAINTENANCE

Most treadmill problems can be solved by following the instructions below. If further assistance is needed, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEMSOLUTION

1.The power does not turn on

a.Make sure that the power cord is plugged into a surge protector, and that the surge protector is plugged into a properly grounded outlet. (See page 7.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.

b.Make sure that the key is fully inserted into the console.

c.Check the circuit breaker located on the frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d.Check the on/off switch located on the frame near the power cord. The switch must be in the on position.

Tripped Reset

On

Position

2.The power turns off a. Check the circuit breaker (see c. above). If the circuit breaker has tripped,

during use

wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in.

c.Remove the key from the console and then reinsert it.

d.Make sure that the on/off switch is in the on position (see d. above).

3. The walking belt

a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of

slows when walked

five feet or less in length.

 

on

 

 

 

b. If the walking belt is overtightened, tread-

b

 

mill performance may decrease and the

 

3Ð4Ó

 

walking belt may be permanently dam-

 

 

 

aged. Remove the key and UNPLUG THE

 

 

POWER CORD. Using the included allen

 

 

wrench, turn both rear roller adjustment

 

 

bolts counterclockwise 1/4 of a turn. When

 

 

the walking belt is properly tightened, you

 

 

should be able to lift the edges of the

Rear Roller Adjustment Bolts

 

walking belt 3 to 4 inches off the walking

 

 

platform. Be careful to keep the walking

 

 

belt centered. Plug in the power cord, insert the key and run the treadmill for a few

 

minutes. Repeat until the walking belt is properly tightened.

 

c. If the walking belt still slows when walked on, call our Customer Service

 

Department toll-free.

17

Image 17
Contents Customer HOT Line QUESTIONS?Model No. HRTL10982 Serial No Table of Contents Important Precautions Page Right Side Before YOU BeginBack Setting UP the Treadmill Performant Lubetm Walking Belt HOW to Plug in the Power CordGrounding Instructions Console Operation Features of the ConsoleRefer to the drawing at the top Diagram of the ConsoleHOW to Turn on the Power HOW to USE the Manual Mode Insert the key fully into the console HOW to USE the Speed Programs and the Incline ProgramsWhenkey. you are finished exercising, remove Enter your age if desiredSeconds HOW to Program the Custom 1 and Custom 2 ProgramsDesired speed and incline settings Follow your progress with the five displays HOW to USE the Custom 1 and Custom 2 ProgramsWhenkey. the program is completed, remove Optional Pulse Sensors Information Mode Personal Trainer ProgramsHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USEProblemsolution TROUBLE-SHOOTING and MaintenancePower does not turn on Slows when walkedBubbles form in the walking belt Walking belt is off-center or slips when walked onBecomes soiled Exercise Intensity Conditioning GuidelinesAGE Workout GuidelinesKey No. Qty Description Part LISTÑModel No. HRTL10982Exploded DRAWINGÑModel No. HRTL10982 Limited Warranty