Healthrider HRTL61706.1 manual Troubleshooting, Problem The power turns off during use

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If you need further assistance, please see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 12. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes, and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The display of the console does not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

11

POWER CORD. With the help of a second person,

 

 

 

carefully tip the Uprights (70, 76) down as shown.

 

 

Remove the three Hood Screws (11) and two 3/4”

 

70

Screws (23). Note: A phillips screwdriver with a shaft

 

 

at least 5" long is required.

 

23

 

 

23

 

76

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model No. HRTL61706.1 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Right Side Before YOU BeginBack Make sure that the power cord is unplugged AssemblyDo not tighten the Upright Bolts yet Do not tighten the Upright Bolts yet Endcap Screws See steps 2 and 4. Fully tighten the twoTighten the Bolts yet Connectors are not Connected Page Small HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeFollow your progress with the display Measure your heart rate if desiredSelect one of the preset programs HOW to USE a Preset ProgramInsert the key fully into the console HOW to USE a Calorie Program Press the Start button to start the programFollow your progress with the display Information MODE/DEMO Mode Optional Chest Pulse SensorHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0107A Qty DescriptionOrdering Replacement Parts Exploded Drawing A-Model No. HRTL61706.1 R0107A Exploded Drawing B-Model No. HRTL61706.1 R0107A Exploded Drawing C-Model No. HRTL61706.1 R0107A Exploded Drawing D-Model No. HRTL61706.1 R0107A Limited Warranty
Top Page Image Contents