Healthrider HRTL61706.1 manual Assembly, Make sure that the power cord is unplugged

Page 6

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed.

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key and your own phillips screwdriver

.

Use the drawings below to identify the hardware used during assembly. Note: If a part is not in the parts bag, check to see if it has been preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly.

3/4" Screw (23)–6

1” Tek Screw (77)–4

1 1/4” Tek Screw (108)–2

Cover Screw (52)–4

3/8" Star

 

Pulse Bar Star

Endcap Screw

Silver Pulse Bar

Console Screw (67)–4

 

Washer (65)–4

(79)–2

Screw (64)–4

 

Washer (83)–4

 

 

 

 

 

2

3/4" Upright Bolt (85)–2

1" Upright Bolt (84)–2

1 1/4" Bolt (63)–4

1. Make sure that the power cord is unplugged.

 

76

 

1

75

 

With the help of a second person, carefully tip

 

 

 

 

 

the treadmill onto its left side as shown. Partially

 

 

 

fold the Frame (26) so that the treadmill is more

 

Post

 

stable. Do not fully fold the Frame until the

 

 

 

 

 

treadmill is completely assembled.

 

Wire

 

Identify the Right Upright (76) which has a

 

 

 

RIGHT sticker. Hold the Right Upright near the

76

 

 

Base (81). Insert the Upright Wire (75) into the

 

 

 

Right Upright until the Upright Wire is extending

 

 

 

from the upper end of the Right Upright. Note:

81

 

 

Make sure that the Upright Wire is extending

 

85

from the side of the post as shown in the inset

 

 

 

drawing. Remove the tie from the Upright Wire.

26

 

 

 

 

 

Thread a 2 3/4" Upright Bolt (85) and a 1" Upright

 

83

84

 

 

Bolt (84) with 3/8" Star Washers (83) into the

 

 

 

Base (81) and the bottom of the Right Upright

 

 

 

(76). Do not tighten the Upright Bolts yet.

 

 

 

6

 

 

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents QUESTIONS? Model No. HRTL61706.1 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Right SideBack Assembly Make sure that the power cord is unpluggedDo not tighten the Upright Bolts yet Do not tighten the Upright Bolts yet See steps 2 and 4. Fully tighten the two Endcap ScrewsTighten the Bolts yet Connectors are not Connected Page Small Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeFollow your progress with the display Measure your heart rate if desiredHOW to USE a Preset Program Select one of the preset programsInsert the key fully into the console HOW to USE a Calorie Program Press the Start button to start the programFollow your progress with the display Information MODE/DEMO Mode Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0107A Qty DescriptionOrdering Replacement Parts Exploded Drawing A-Model No. HRTL61706.1 R0107A Exploded Drawing B-Model No. HRTL61706.1 R0107A Exploded Drawing C-Model No. HRTL61706.1 R0107A Exploded Drawing D-Model No. HRTL61706.1 R0107A Limited Warranty
Top Page Image Contents