4.It will beep for 12 seconds to indicate the completion of workout which is preset. Press any key to stop beeping.
REMARKS
1.It is suggested to preset only one item. If more than one item is set, the first to reach the preset value will sound the alarm.
2.For PU L SE window, the monitor will not beep after reaching the preset value. The display will be flashing continuously while actual heartbeat detected is over the preset value.
3.When pressing SE L EC T key, the setting will start
from TIME , DISTA NCE , C A LOR I E S & PU L SE . To
skip from the setting, please do not press SE L EC T again and wait until the display stops flashing after programming functions desired. Then, the monitor will come back to normal and ready to be operated.
ACCUMULATED DISTANCE:
Press and hold key, the window
will present ACCU M U L AT E D DISTA NC E that is
resulted from total distance users have been exercising. After releasing the key, all the displays will reset to zero.
SPEED:
Current speed will be shown by the top line of LCD when exercising.
DISTANCE:
The distance of each workout will be displayed by the 4th line of the LCD.
CALORIE:
The calories burned will ne displayed by the 2nd line of LCD.
PULSE: (Perfect pulse system)
To display your current heart rate on the lower right LCD in beats per minute (BPM). Place the palms of your hands on the both of the contact pads and the monitor will show up your current beat rate in beat per minute (BPM) on the LCD display. (Please see the drawing below.)
NOTE:
1.If pulse value is not preset, the monitor will show the default value at 90BPM.
2.If no Pulse Signal input within 16 seconds,
the display will indicate ”P”. It is a power saving device. Customers can press the up & down keys to restart Pulse function.
M A I N T E N A N C E
The equipment requires very little maintenance. Check, however, from time to time that all screws and nuts are tight. Clean the cycle with a damp cloth. Do not use solvents.
NOTE! Never remove the protective covers. NOTE! The brake forms a magnetic field
which may damage the mechanism of a watch or
G B
O W N E R ' S M A N U A L • F 2 O O
the magnetic identification tape of a credit or cash card if they come into immediate contact with the magnets. Never attempt to detach or remove the magnet fork of the magnetic brake.
If you notice a malfunction during use, contact the dealer. Always give the model and serial number of your device, please state also the nature of the problem conditions of use and purchase date.
In spite of continuous quality control, individual defects and malfunctions may occur in individual components. It is in most cases unnecessary to take the whole cycle for repair, as it is usually sufficient to replace the defective part.
CHANGING BATTERIES
If the meter display fades considerably or completely, change the batteries.
Detach the lid of the battery casing at the back of the meter and remove the old batteries. Place the new batteries in the holder (2 x 1.5 V AA) and push the battery casing lid back into place.
T R A N S P O R T A N D S T O R A G E
The cycle is easy to move by pushing along on the integrated transport wheels. Tilt the cycle from the front and push along the floor on the wheels at the front support.
To prevent malfunctioning of the cycle, store in a dry place with as little temperature variation as possible, protected from dust.
D I M E N S I O N S |
|
| |
Length | ......87 cm / 34” | Width | 61 cm / 24” |
Height | ....127 cm / 50” | Weight ... | 31 kg / 69 lbs |
All Tunturi models are designed to meet the electromagnetic compatibility directive, EMC and are affixed with the CE conformity marking.
NOTE! The instructions must be followed carefully in the assembly, use and maintenance of your equipment. The warranty does not cover damage due to negligence of the assembly, adjustment and maintenance instructions described herein. Changes or modifications not expressly approved by Tunturi Oy Ltd will void the user's authority to operate the equipment!
Due to our continuous policy of product development we reserve the right to change specifications without notice.
5