NordicTrack NTEL05900 user manual

Page 7

6.Remove the four M10 Nylon Locknuts (not shown) from the welded bolts on the front of the Frame (1).

Lay a cloth over the front of the Frame (1) to protect it from scratches. Lay the Upright (2) in the position shown. Connect the Extension Wire (51) to the Reed Switch Wire (50).

Next, connect the Resistance Cable (57) to the Extension Cable (93) in the following way:

Refer to drawing A. Pull up on the metal bracket on the Extension Cable (93), and insert the tip of the Resistance Cable (57) into the wire clip on the Extension Cable as shown.

Refer to drawing B. Firmly pull the Resistance Cable (57) and slide it into the metal bracket on the Extension Cable (93) as shown.

Refer to drawing C. Using pliers, squeeze the prongs on the upper end of the metal bracket together.

7.Align the two holes in the front of the Upright (2) with the two welded bolts on the front of the Frame (1).

Next, pivot the Upright (2) about halfway to a vertical position. Refer to the inset drawing. As you raise the Upright, look into the lower end and make sure that the metal bracket on the Extension Cable (93) does not get caught on the Upright or the Frame

(1). In addition, feed all slack Extension Wire (51) and Reed Switch Wire (50) into the Upright. Continue to raise the Upright until the four welded bolts are inserted through the bracket at the bottom of the Upright.

Lift the front of the Incline Frame (5). Tighten an M10 Nylon Locknut (26) onto each welded bolt.

8.Identify the Left Pedal Arm (3), which has an “L” sticker on it. Next, identify the Left Pedal (41), which has the letter “L” molded onto the bottom.

Turn over the Left Pedal Arm (3) as shown. Insert the three plastic posts on the Left Pedal (41) into the three indicated holes in the Left Pedal Arm. Make sure that the Left Pedal is turned as shown. Attach the Left Pedal with three Pedal Screws (43).

Attach the Right Pedal (not shown) to the Right Pedal Arm (not shown) in the same way.

6

 

2

 

 

 

 

 

 

 

57

 

 

 

93

 

 

 

51

 

 

 

50

Welded Bolts

1

 

A

B

 

C

Metal

 

 

57

Bracket

 

 

 

 

 

57

 

57

 

 

 

93

 

93

93

7

 

 

 

 

2

 

 

 

 

26

5

 

 

1

 

 

 

Welded Bolts

 

 

 

 

2

 

93

 

51

 

 

50

 

 

 

 

 

 

1

 

8

 

 

 

 

43

 

 

 

 

 

Welded

 

 

 

Bolt

3

 

 

 

 

 

 

Open Side

41

 

 

Plastic Posts

 

 

 

7

Image 7
Contents Model No. NTEL05900 Serial No Number Decal QUESTIONS?Customer HOT Line Table of Contents Important Precautions Right Side Before YOU BeginFront BackAssembly Locknut the Incline Bracket must pivot easily Page Center the Arm Axle HOW to Adjust the Resistance HOW to USE the Elliptical CrosstrainerIncline Adjustment HOW to USE the Upper Body ArmsTraining zone Battery InstallationHOW to Operate the Console Description of the ConsoleBattery Replacement Maintenance and TroubleshootingLubricating the Incline Bracket Conditioning Guidelines Suggested Stretches Qty Description Part LIST-Model No. NTEL05900R1101A 2667 31 59 Limited Warranty HOW to Order Replacement Parts