ParaBody 425101 IN. WASHER.S,and one, PLAY,.YET Allowingthe Press Armto Rotatefreely, 07/22/96

'~* Removethe PAPA.GLIDEST/UPSfrom the paper backing and firmly apply themtO all shownsurfaces.

,Carefully slide the PRESSADJUSTMENTTUBEinto the RECEIVINGTUBE.(MAKESURE"],'HESPRINGPIN BARRELON THE RECEIVINGTUBE IS ON THE SAMESIDE AS THE HOLESIN THE PF~SS ADJUSTM~IlNT TUBE)

Insert two (2) 1/2- IN. FLANGEBEARINGSinto the PRESSLEVERas shownon drawing.

Assemble the PRESSADJUSTMENTTUBEto the PRESSLEVERas shown on drawing, using one (1) 1/2 X

BOLT,two (2) 1/2 IN. WASHERS,and one (1) I/2 IN. LOCKNUT.(TIGHTEN THECONNEL-i'IONENOUGH

TO .REMOVETHE PLAY, YET ALLOWINGTHE RECEIVING TUBE TO ROTATEFREELY) Insert two (2) .3/4 IN. FLANGEBEAP,.INGSinto the PRESSARM~s shownon the drawing.

¯'. Hold the PRESSARMbetweenthe. REARand ~MIDDLEUPRIGHTSas shownin on drawing, and'sIide the I0-I/4 IN. AXLEthroughthe MIDDLEUPRIGHT,th~PRESS.A~RM,:and.througfi the COLLARon.the REARUPRIGHT.To SECUREthe AXLEin place, insert two (2) 3116 X 3/8 IN. SETSCREWS,into the COLLARSon the UPRIGHTSand tighten it downonto the AXLE(SEE. DETAILC)

10.Insert two (2) I~ IN. FLANGEBEARINGSinto the RECEIVINGTUBEas shownon drawing.

I1.	Assemblethe	RECEIVINGTUBEto	the PRESSARMas shownon drawing, ~tsing one (1) I/2 X 3.-I/2 IN. BOLT,two
	1/2 IN. WASHER.S,and one		(I) 1;2 IN. LOCKNUT. (TIGHTENTHE CONNECTIONENOUGItTO REMOVE
	PLAY,.YET	ALLOWINGTHE PRESS ARMTO ROTATEFREELY)

12.Assemble the PUSH/PULLCABLEto the SPRINGPIN HOUSINGand to the L-BRACKETon fl~e RECEIVING TUBEas shownin (DETAILD), using the f'ollowing steps:

¯Threadthe first I/4-2~i IN. NUTto the bottomof the threaded end of'the CABLEAllow.

¯other I/4-28 IN. NUTto hang loose on the exposed CABLE.until the SPRINGPIN ASSEMBLYisattached.

¯Securely assemble the SPRINGPIN ASSEMBLYto the SPRINGPIN BARREL(!:!. IMPORTANT!!!

TIGHTEN THE NUT OF THE SPRING PIN ASSEMBLYSECURELY)

¯Swing the PRESSARMup until the SPRINGPIN of'the PUSH/PULLCABLEengages in one of the adjustmentholes.

¯Threadthe secondI/4-25 IN. NUTonto the threaded end of the CABLE,and cinch the two (2) 114-2~.IN. aroundthe fiat.

¯Use the extra thread on the end of.the CABLE'toadjust out slack, ( !!! DONOTADJUSTOUTTOFAR1!!

ALWAYSALLOWSPRING PIN ASSEMBLYTO FULLY ENGAGE)

¯Attach one (1) ADHESIVECLIP to the RECEIVINGTUBEand snap the CABLEinto it.

"SECURELYtighten all loose frame cormectiot~s madeto this point. (!!! IMPORTANT!!! TOASSUR~PROPER"

.:~FUNCTION OF THE 425, THE LOOSEFRAMECONNECTIONSMUSTBE TIGHTENEDIN THE FOLLOWING ORDER)Tighten the:

¯REARUPRIGHTto the BASEand to the TOPBOOM.

¯PRESSBASEto the REARand MIDDLEUPRIGHTS.

¯PRESSBASEto the BASE.

.= MIDDLEUPRIGHTtothe BASE'and to the .TOPBOOM.

¯FRONT.UPRIGHTto the.BASE.

NOTE: DO NOT TIGHTEN THE FRONT UPRIGHT TO THE TOP BOOMAT THIS TIME,

14.SECURELYassemble the other BACK/SEATPADto the FRONTUPRIGHTas shownon drawing, using two (2) 3/~

.3 IN. BOLTS,two (2) 3/8 IN. LOCKWASHERS,and two (2) 3/g IN. WASHERS.

THIS CONCLUDESTHE ASSEMBLYOF (LEVEL 4)

9

07/22/96