Place with one 1 Thumbscrew, Assemblysecuilily. ~

WHEELS DO NOT ROTATE FREELY AFTER THE BOLTS ARE TIGHT, REMOVE WASHERS.)

SECURELYassemble~heSEATPADto theADJUSTABLEPRESSSEATas shownon/rzwing,usingtwo(2)3;8X 314IN.BOLTS,two(2)318IN.LOCKWASHERS,andtwo(2)318IN.WASHERS.

PullbacktheSPRINGPrNon thePRESSBACKSUPPORTand.slidetheADJUSTABLEPRESSSEATintothe RECEIVINGW'ELL.EngagetheSPRINGPINintooneof theadjustmentholes.SecuretheADJUSTABLEPRESSSEAT

in place with one (1) THUMBSCREW.

SECURELYassembletheBACKPADt6 thePRESSBACKSUPPORTas shownondrawing,usingtwo(2)3/8X 3 IN. BOLTS,two(2)3/~IN.LOCKWASHERS,andtwo(2)3/8IN.WASHERS.

Inserttwo(2)I/2IN.FLANGEBEARINGSintothePRESSSUPPORTTUBEasshownon drawing.

"..SECURELY"assemblePRESSBACK.theSUPPDRTto the.PRESSsuPPORTTU.BE,~sshownin drawing;usingone(I) I~.X3~I/'2IN.:BOLT/:two"(2)I/2IN.~W.ASHERS,.one~m~d(I)I/2IN~.LOCKNUT.(~IGHTENTHECONNECTION ENOUGH TO.REMOVE'THE:PLAY,~/ET.ALLOWINGTHEPRESS BACK SUPPORT..TO ]ROTATE FREELY)

SECURELYassembleone(I)ID_I~ SPRINGPIN.ASSEMBLYto theSPRINGPINHOUSING,of thePRESS SUPPORTTUBERs shownin (DETAILE). (!!!IMPORTANT!!!TIGHTENTHE NUTOi~ .THESPRING

ASSEMBLYSECUILI'LY). "~ ...................... -'

SECURELYassemble, the BEARINGHOUSINGand the CENTERPULLEYBRACKETto the ]FRONTUPRIGHT~s shown.ondrawing, using two(2) 1/2 X 3-1/2IN. BOLTS,four (4) I/2 IN. WASHERS,and two (2) 1/2 IN. LOCK

(THE CONNECTORPLATES ON THE BEARING HOUSING AND THE CENTER PULLEY BRACKETHAVE SLOTTED HOLES. SHIFT THE BEARING HOUSINGDOWNAND THE CENTER PULLEY BRACKETUP AS

FAR AS POSSIBLE)

¯Assembletwo(2)3/4IN.THRUSTWASHERSandtwo(2)PECCAMSto theLEFTandRIGHT:FECARMS,as shown

¯ondrawing.

Insert four (4) .3/4 IN. FLANGEBEARINGSinto the BUSHINGSof the BEARINGHOUSING,as shownon drawing.

ll.InserttheLEFTandRIGHTPECDECARMSthroughthe3/4IN.FLANGEBEARINGSin theBEARINGHOUSING ontheirrespectivesidesasshownondrawing,andSECURE~heminplacewithtwo(2)3/4I.D.STARLOCKCOLLARS.

12.¯ ..Attach two (2) 1 X 1 IN. CARKIAGEGUIDESto the ANGLEon the BEARINGHOUSINGwhere the PECCAMS ,make contact with the ANGLE.

.Slidet~,.o(2)4 X 12 ROLLERPADSontothe LEFTandRIGHTPE'C.D~.'ARMS,CumirtheROLLERPADis FLUSH ,~iththe bottomof.theARMS.(IF A LUBRICANT-ISREQUIRED,COATTHE INSIDEOF THEROLLERPAD "WITH RUBBING ALCOHOL ALSO, ROTATING THE PAD WHILEP.USHINGUP WILL HELP TO EASE 'ASSEMBLY)

14.SECURELYassembletwo(2)3/8IN.SPRINGPINASSEMBLIESto theSPRINGPINBARRELS,ofthePECCAMS sho,h'nin (DETAILB). (!!! IMPORTANT!!! TIGHTENTHE NUTOFTHE SPRINGPIN ASSEMBLYSECURELY)

15.LOOSELY'asscmble(2).two3-I~X 1 IN..P.ULLEYSandtwo(2)2-3/,~IN,CABLERETAININGCLIPSto theCENTER PULLEYBRACKETasshownin (DETAILD),usingtwo(2)3/8X 2 IN.BOLTS,two(2)3/$IN.WASHERS,and

(2)3/8 IN~ LOCK NUTS.(NOTE: THIS CONNECTIONWILL BE TIGHTENEDAFTER THE CABLEHAS BEEN ROUTED)

.... placewiththree(.3)I/4.INCAP.NUTS.

THIS CONCLUDES THE ASSEMBLY OF (LEVEL

425101 HOME GYM ASSEMBLY PARTS LIST .(LEVEL'6)

07~6