ParaBody 425101 ARM to Rotate Freely, Followed ~n step, PEGSEATdownto desired height. Release

Page 7

SECURELYassemble the WEIGHTsTACKSHAFTto the HEADPLATEas shown on drawing, using one (I) 3/2 X 1~ IN. BOLT,one (1) 3/8 IN. LOCKWASHER,and one (I) 3/8 IN. WASHER.

Snaptwo(2)W3~IGHTPLATEBUSHINGSeach,intofiReen(}5)WEICHTPLATESshown in (DETAIL B)(IF.

ASSEMBLINGA 200 LB. STACK AT THIS TIME, SNAP TWO (2) WEIGHT PLATE BUSHINGSEACH INTO THE RE.~tAININGFIVE (S) WEIGHTPLATES)

USINGEXTRE~TECAREslide all fifteen (or twenty) WEIGHTPLATESdown over the CUIDIERODSonto the WEIGHTSTACKCUSHIONSas shown on drawing. (MAKESURE THATTHE KEY HOLESOF THE WEIGHT PLATES ARE ALL FACING THE SAME WAY)

Slide t~e HEADPLATEASSEMBLYdown over the GUIDERODSonto the WEIGHTSTACKas shown on drawing.

Swing th~ GUIDERODSunder the TOPBOOMas shownon drawing, and hold in place with two (2) GUIDERODPINS.

¯Auach the-WEIGHTSTACK-LABELStothe ..W.EIGHTSTACK:asshown on.drawing. Also .insertthe WEIGHTSTACK SELECTORPIN into the first WEIGHTPLATTEof the WEIGHTSTACK.

II.SECURELYAssemble one (I) ~/8 IN. SPRINGPIN ASSEMBLYto the SPRINGPIN HOUSING,of the LEG CURL/~XTENSIONARMas shown in (DETAIL C). (Ill IMPORTANT!!! TIGHTENTHENUTOF THE SPRING PIN ASSEMBLYSECUREL@.

12.Attach eight (8) PAKAGLIDESTRIPSto the AD.IUSTABLEROLLERPADSLEEVEas shown in (DETAILD),

.usingthe. followingsteps:

¯Thoroughlyclean all surfaces wherethe PARAGLIDESTR/PSare robe attached.

~.Removethe PAKAGLIDESTRIPSfromthe paper backing and firmly apply themto all showasurfaces.

13.Removethe 2 IN. SQ. ENDCAPfrom the bottom of the LEGCURLEXTENSIONAR~,I, pull back the SPRINGPIN, and Insert the ADJUSTABLEROLLERPADSLEEVEas shownin (DETAILE). Release the SPKI'NG,PIN into one of the adjustmentholes, and reinsert the 2 IN. SQ,ENDCAP.

15.Assemble the two (2) ROLLERPADSto the LEGCURLEXTENSIONARMas shown on drawing using one (I) ROLLERPADSHAFT,two (2) PLASTICWASHERS,and two (2) 9/I 6 MUSHROOMCAPS. (MAKESURE THE ROLLER PAD SHAFT IS INSERTED THROUGHLARGE HOLE ON THE ADJUSTABLEROLLER PAD SLEEVE)

16.¯ AssembletheLEGCURI./EXTENSIONARMto theFRONTUPRIGHTusingthefollowings~eps:

¯". Insert twO(2) 1/2 IN. FLANGEBEARINGSto the FRONTUPRIGHTas shown n drawing..

¯Assemble the LEGCURL/EXTENSIONARMto the FRONTUPRIGHTas shoumon drawing, using one (I) I/2 X 3-I14 IN. BOLT,two (2) I/2 TN. 3k'ASHERS,and one (1) I}2 IN. LOWI-I~IGI-IT LOCKNUT.(TIGHTEN CONNECTIONENOUGHTO REMOVETHE PLAY, YET ALLOWINGTHE LEG CURL/EXTENSiON

ARM TO ROTATE FREELY)

¯* Attach one (1) 1-1/4 IN. SO..RUBBERBUMPERto the FRON'rUPRIGHTwhcr~ the LEGCURL/EXTENSION ARMmakes contact. (SEE DRAWING).

17.Pre-.assemblethePECSEAT,usingthefollowingstep's:

¯:SECURELY~assembleoneof.theBACK/SEAT.PADStothePEG.SEATasshownondrawing,usingtwo(2)318 3 IN.BOLTS,two(2)3/8I"NLOCK.WASHERS,andtwo(2)3/8IN.WASHERS.

Assembletwo(2)ROLLERPADSto thePEGSEATas shownon drawing,usingone(I)ROLLERPADSHAFT, andtwo(2)9/I6 MUSHROOMCAPS.

__I_3.......: .A.~.n.~c/~ht(8)PAP,.AGLIDESTR.IPStotheFRONTUPRIGHTasshownin(DETAILF),andusilngthedirections

 

followed ~n step I2.

"

',

Pull back the SPRINGPIN on the FRONTUPRIGHTand insert

the PEGSEATdownto desired height. Release the

 

SPRINGPINand allow it. to engageinto the adjustment.holes. Use the THUMBSCREW~o tighten the PEGSEATin

 

place.

 

Image 7
Contents Homegym Assembly Instructions Bolt Length ~ Bolt Length Ruler CQNNETI, NIN. Locknut 2X4IN.BOLTIN. Lockwasher 8INLOCK.NUTIN. LOCK.NUT PLAY, YET Allowingthe Press Leverto RotatefileelyDrawing IAR~WAREThis Concludes the ASSElVIBLY of Level Pecseat WEIGHTSTACKSFL~.FTWELDMENTS/PARTS NAME/DESCRIPTION QTY HeadplatePlace ARM to Rotate FreelyFollowed ~n step PEGSEATdownto desired height. Release6538401 IN. Locknut Control Lever IN. Flangebearing32 X 3/16 IN. Screw King PressarmPLAY,.YET Allowingthe Press Armto Rotatefreely Tighten the NUT of the Spring PIN AssemblysecurelyAlwaysallowspring PIN Assemblyto Fully Engage IN. WASHER.S,and one4X.12INROLLER.PADS Count ALL Parts Before Beginning AssemblyIN. Wheel BackpadPlace with one 1 Thumbscrew ASSEMBLYSECUILILY. ~FAR AS Possible 6535901 Removepulleysfor Ease of Installation~,VELDMENTS/PARTS NAME/DESCRIPTION 6540301Routethe LEGCABLEas shownin drawing NAME/D ESCtLIPTIONPulleybracket Center OE the Cable~ELDMENTS/PARTS ~EMPage ~ PARAE, ODY,INC Page Detaile SEED~~,,AIL,,B ETA!L,,A Detail B Detail F Page Latbar Page Shown ~ PARABODY,INc Page PARABODY,INC Detail ~ ~L PARABODY,.~,~Y.INC Level ~ PARAt3ODY,INC