Models 91TI, 90T Treadmills

TOOLS REQUIRED: Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters

NOTE: Proceed with the following steps immediately after attaching the DISPLAY CONSOLE as described in the Assembly Instructions. Do not install the ACCESSORY TRAYS or PUSH RIVETS.

1.Remove the nine SCREWS (a) from the rear of the console securing the FRONT CONSOLE

(b) to the REAR CONSOLE (c). Carefully lift the FRONT CONSOLE. Set the FRONT CON- SOLE and SCREWS aside.

2.Route the main wire harness (D), POWER CORD (d), and COAXIAL CABLE

(e) through the LARGE CABLE CLIP (f) located at the left inside of the REAR CONSOLE (c). Route the POWER CORD and COAXIAL CABLE through the LARGE CABLE CLIP (f) located at the center inside of the REAR CONSOLE. Continue routing the POWER CORD and COAXIAL CABLE through the notch at the top of the

REAR CONSOLE.

3. Locate the REMOTE CONTROL (g). Configure the REMOTE CON- TROL for a VERTICAL (C-V) installation. Secure the REMOTE CONTROL to the left end of the ERGO CROSSBAR (13) as shown. Be sure the CABLE TIES (C-V) are pulled tight and trim the excess

CABLE TIES.

4. Route the REMOTE CABLE (h) along the LEFT HANDLEBAR (1). Secure the REMOTE CABLE using two CABLE TIES (j) at the locations shown. Be sure the CABLE TIES are pulled tight and trim the excess CABLE TIES. Route the remaining REMOTE CABLE through the CABLE CLIP (k) located on the bot- tom left of the REAR CONSOLE (c) and up through the LEFT ACCESS PANEL. Route the REMOTE CABLE through the LARGE CABLE CLIP (f) located at the center

inside of the REAR CONSOLE. Continue routing the REMOTE CABLE through the notch at the top of the REAR CONSOLE.

5.Connect the MAIN WIRE HARNESS (D) and HANDLEBAR WIRE HARNESS (B) to the back of

the FRONT CONSOLE (b). With the POWER CORD (d), COAXIAL CABLE (e) and REMOTE CABLE (h) oriented in the TOP CONSOLE NOTCH as shown, secure the FRONT CONSOLE (b)

using the nine previously removed SCREWS (a). Tighten the SCREWS securely. Replace the ACCESS PANELS (C).

NOTE: Be careful not to pinch the REMOTE CABLE (h) when replacing the ACCESS PANELS (C).

6.Install the ACCESSORY TRAYS (17 & 18) as instructed in the Assembly Instructions.

7.Remove the LEFT and RIGHT UPPER HANDLEBAR ENDCAPS (m) and discard them.

8.Position the BRACKET TUBE (n) as shown and slide the ends into the

HANDRAILS (1 & 2) until fully seated.

9. Install the four SET SCREWS (o) into the BRACKET TUBE MOUNT- ING ARMS (p) and tighten the SET SCREWS securely. Do not over- tighten the SET SCREWS.

10. Attach the ENTERTAINMENT CONSOLE (q) to the UPPER MOUNT- ING PLATE (r) using four SCREWS (s) and NYLON WASHERS (t). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.

11. Connect the COAXIAL CABLE (e), REMOTE CABLE (h), and POWER CORD (d) to the rear of the ENTERTAINMENT CONSOLE (q) as shown under Console Cable Connections at the end of this manual.

12. Unwrap the MAIN WIRE HARNESS (D) located at the base of the LEFT UPRIGHT (1). Route the MAIN WIRE HARNESS, POWER CABLE and COAX- IAL CABLE under the CROSS FRAME MEMBER (E). Connect the 10-PIN CONNECTOR (10P) of the MAIN WIRE HARNESS to the corresponding JACK

(F) locates at the top of the CONTROL BOARD (G).

LCD Entertainment Ready specifications

Life Fitness LCD Entertainment Ready is an innovative solution designed to enhance the workout experience while providing an outlet for entertainment and motivation. This state-of-the-art display technology is integrated into a wide range of Life Fitness cardio equipment, allowing users to stay engaged during their exercise routines. The LCD screens offer a vivid display that provides easy access to entertainment options, workout stats, and various fitness programs.

One of the standout features of Life Fitness LCD Entertainment Ready is its versatility. The screens are compatible with various entertainment platforms, enabling users to connect their personal devices to stream their favorite shows, movies, or music. This feature not only helps to make workouts more enjoyable but also encourages longer duration exercise sessions as individuals become immersed in their content.

In terms of technology, the Life Fitness LCD systems are equipped with high-definition screens that provide clear and concise visuals. The user interface is intuitive, allowing for easy navigation of multiple options, whether it’s tuning into a TV show or monitoring workout progress. Additionally, the screens are often touch-sensitive, providing a seamless interaction experience for users.

Another key characteristic of this entertainment system is its focus on user engagement. The interface not only provides entertainment but also promotes fitness goals through real-time feedback. Users can track calories burned, distance traveled, and heart rate. This information helps in maintaining motivation and allows individuals to adjust their workouts for optimal performance.

Moreover, Life Fitness prioritizes practicality and ease of installation. The LCD Entertainment Ready feature is designed to be integrated easily into the Life Fitness equipment lineup. Whether it's treadmills, stationary bikes, or ellipticals, this feature enhances the existing functionalities of the machines without compromising space or usability.

In conclusion, the Life Fitness LCD Entertainment Ready system exemplifies the merging of fitness and technology, creating an engaging workout environment. With its high-definition displays, entertainment compatibility, and user-friendly interface, it transforms routine exercise into a more enjoyable and motivating experience. This innovation showcases Life Fitness’s commitment to enhancing health and well-being through advanced technology and user-centric design.