Image IMTL39620 user manual Rectangular Hole Bend 107 Ground Wire 108

Page 7

2.Identify the Right Upright (10), which has a large rectan- gular hole near the upper end (see drawing 2b). Have a second person hold the Right Upright near the Wire Harness (17). Insert the end of the Wire Harness into the Right Upright and out of the rectangular hole near the upper end as shown. If necessary, use needlenose pliers to pull the Wire Harness out of the hole.

3.Make sure that the Right Upright (10) is turned so it bends in the direction shown. Insert two 3” Bolts (47) with Washers (29) through the Base (82) and hand tighten the Bolts into the lower end of the Right Upright.

With the help of a second person, tip the treadmill onto its other side and repeat steps 1 through 3. Note: There is not a wire harness in the Left Upright (not shown). An extra Base Pad my be included.

4.With the help of a second person, set the treadmill flat on the floor so that the Right Upright (10) and the Left Upright (not shown) are vertical.

Hold one of the Handrails (85) near the Right Upright

(10). Insert the end of the Wire Harness (17) into the bot- tom of the Handrail and out of the indicated hole. Using the Silver Screw (107), attach the end of the ground wire to the small hole in the side of the Handrail.

5.Have a second person hold the Console Base (87) and the Handrail (85) in the position shown. Touch the Right Upright (10) to discharge any static. Insert the Wire Harness (17) through the two Plastic Ties (108) on the Console Base. Find the 3-wire connector on the end of the Wire Harness. Insert the connector into the red socket beneath the Console Base. The connector should slide easily into the socket and “snap” into place. If the connector does not slide easily and snap into place, turn the connector and then insert it. If the connectors are not inserted properly, the Console may be damaged when the power is turned on.

Insert the 5-wire connector into the black socket in the same way. Make sure that the connectors and wires ap- pear as shown in the inset drawing. Insert the excess Wire Harness (17) down through the Handrail (85).

Securely tighten the Plastic Ties (108) to prevent the Wire Harness (17) from slipping. Then, cut off the ends of the Plastic Ties.

2a

 

10

 

 

 

 

 

 

 

17

2b

Rectangular

10

 

 

Hole

 

 

 

 

 

17

 

 

3

 

82

47

 

 

10

29

 

Bend

 

 

4

 

107

 

 

Ground

 

17

 

Wire

 

 

 

Hole

 

 

 

 

85

 

 

10

 

 

5

87

 

 

 

108

 

 

 

 

 

85

 

 

 

 

 

17

 

 

 

5-wire

10

 

 

3-wire

 

17

 

 

7

Image 7
Contents Model No. IMTL39620 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Page Right Side Before YOU BeginLeft Side Driver Adjustable wrench Wire cutters AssemblyMake sure that the power cord is not plugged Rectangular Hole Bend 107 Ground Wire 108 118 HOW to Plug in the Power Cord Operation and AdjustmentPerformant Lubetm Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerHOW to USE Personal Trainer Programs Follow your progress with the displays HOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoAdapter Audio Cable HOW to Connect Your VCRPrograms OUR WEB Site HOW to USE Programs Directly fromInformation Mode HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Key Qty Description R0203AExploded Exploded DRAWING-Model No Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT